Mitsubishi Electronics HS-S8300E(BRS) Features and Functions, Rear View, Reset button

Page 6

FEATURES AND FUNCTIONS

REAR VIEW

1

2 4 6 9 A

 

3 5 7 8

 

 

 

 

 

 

SET RST REC GND ALM MODE

 

CLK CALL

 

IN

 

 

 

OUT

 

RESET

 

 

 

 

 

 

 

 

 

 

 

IN OUT

S-VIDEO

É MIC

IN

OUT

 

REMOTE

 

AUDIO

IN

OUT

 

 

 

 

VIDEO

 

KJ I H G

F ED

B

IN

RS-232C

OUT

C

N

•Ensure the power cord is not plugged into the mains outlet before connecting to any rear terminals.

1AC power socket

This socket connects to the power cord. Insert the cord firmly.

2SET IN terminal

Input terminal for alarm recording. The alarm sensor is connected here.

3RST (RESET) IN terminal

Input terminal to stop alarm recording when “ALARM REC DURATION” of the “RECORDING SET UP” menu is set to “MAN1”. The alarm reset switch is connected here. This terminal can also be used to set the on-screen clock when set to any mode other than “MAN1”.

4REC IN terminal

Input terminal to start/stop recording. Also, use this terminal for series recording (P.17) or synchronous recording (P.18).

5GND (GROUND) terminal

When a lead connected to other terminals requires a ground, connect the ground lead here.

6ALM (ALARM) OUT terminal

Output terminal to indicate alarm recording to an external alarm.

7MODE OUT terminal

Output terminal to indicate the VCR’s mode of operation. Selected by setting “MODE OUT” on the “REAR TERMINAL” menu.

8CLK (CLOCK) OUT terminal

Output terminal to control an external camera switcher.

9CALL OUT terminal

Output terminal to indicate when tape has finished recording or if there has been a problem during recording.

ARESET button

When pressed, the present time, alarm recording list, power loss list and the number of tape use will be erased. While the button is pressed, the power is cut off from the VCR. If there is a cassette tape in the VCR and the button is released, the power indicator will light and the tape will fast forward for a few seconds. The VCR will then switch off.

BRS-232C IN terminal (D-SUB 9pin)

Input terminal to connect with a personal computer via RS-232C cross cable.

CRS-232C OUT terminal (D-SUB 9pin)

Output terminal to connect the VCR with other VCRs via RS-232C cross cable.

DS-VIDEO OUT connector

Output connector for video signal. (S-VIDEO connector)

ES-VIDEO IN connector

Input connector for video signal. (S-VIDEO connector)

FREMOTE jack

Remote control is possible by connecting the optional remote control unit (R-7100) here. Refer to page 40.

GVIDEO OUT connector

Output connector for video signal (BNC connector). If the power switch is turned OFF, the signal from the VIDEO IN connector is looped out to this connector.

HVIDEO IN connector

Input connector for video signal (BNC connector).

IAUDIO OUT connector

Audio output connector (RCA pin).

JAUDIO IN connector

Audio input connector (RCA pin).

KMIC IN jack

Input jack for a microphone with 600 ohms impedance.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HS-S8300EBRS VHSCondensation is the Enemy of Video Recorders When not in USEInstallation Location Unplugging the Mains LeadContents FeaturesFeatures and Functions Front ViewFluorescent display REC Fluorescent DisplayFeatures and Functions Reset buttonRear View Connecting with Other Equipment SensorSetting the Menus Present time display will appearPresent Time Display Timer Program DisplayTime Date Search Setting the Menus Recording SET UPRear Terminal Maintenance First Time SET UP Setting the Present Time Display modeFRI Setting the Present Time Setting the Present Time to the Exact SecondUnloading Loading and Unloading the Cassette TapeLoading Preventing Accidental ErasureManual Recording REC ModeLock Mode Recording Check FunctionNumber of Tape USE Repeat REC Times Stop Rewind Repeat AlarmprotRepeat Recording Recommended Number of Tape USESynchronous Recording Manual RecordingONE SHOT/INTERVAL Recording ConnectionAdditional Features Timer Recording Order to Avoid Mistakes When Using the Timer Symptom Fault ActionExternal Time Clock Adjustment Alarm RecordingAlarm Recording Connection 1st VCRSetting for Alarm Recording Emergency RecordingLocating the Start of Alarm Recordings Alarm RecordingAlarm Record Time Display Index SearchPlayback Mode PlaybackAudio Playback Direct Shuttle Ring Special Effects PlaybackShuttle Ring Still PicturePicture Quality Adjustment Adjustment During PlaybackTracking Adjustment When the picture is vibratingUsing with the Personal Computer Configuring the Time Lapse VCRConnecting the VCR to a personal computer Setting Data BIT Length RS-232C SettingSetting Transmission Rate Setting Stop BIT LengthData Communications Settings Using with the Personal ComputerConnecting to a Personal Computer Physical protocol of RS-232CCommand received Command Commands sent to the VCR FormatPower on command Command carried outCommand received VCR02 Command ParameterCommand for fast forwarding VCR02 Command carried out VCR02Commands and Responses 171=TIME Date Adjust + STOP=0, REWIND=1, REPEAT=2 Error codes +0=SERIES, 1=REC-START/STOP =SYNC RECCause Remedy To Turn OFF the Indication Self Diagnostic FunctionFluorescent Monitor DisplayBefore Calling for Service Symptom RemedyIs the Lock indicator illuminated? Control INPUT/OUTPUT Signals and Circuits Control INPUT/OUTPUT Signals and Circuits CircuitLabel B-7 Specifications Connectors872C193C3
Top Page Image Contents