Mitsubishi Electronics HS-S8300E(BRS) operation manual Control INPUT/OUTPUT Signals and Circuits

Page 39

CONTROL INPUT/OUTPUT SIGNALS AND CIRCUITS

2SET/ RST/ REC IN terminals (screw)

Active:	When input terminals are short-circuited to GND or “L” level voltage (0 - +1.6V) applied.
Time for active: 0.1 sec or over.
Non active:	Open the input.

		DC5V
SET/RST/REC IN 22kΩ		10kΩ
SET/RST/REC IN 22kΩ
	0.047∝ F
	GND
<Interface circuit inside the VCR>
2ALM/ MODE/CALL OUT terminals (screw) Active:	“L” level voltage (0 - +0.4V) output; max. drive current 50mA(+5V DC)/
	10mA(+24V DC)
Non active:	Open; max. voltage +24V DC

ALM / MODE/ CALL OUT

GND

2CLK OUT terminal (screw)

DC12V

10kΩ

CLK OUT

10kΩ

GND

<Interface circuit inside the VCR> CLK OUT signal

• When “F” is selected in REC of CLOCK OUT mode in 3H recording.

+12V

10msec

•During recording in L12H - 960H recording mode.

+12V

8msec

• When except “F” is selected in REC of CLOCK OUT mode in 3H recording.

+12V

20msec

Image 39

Contents VHS HS-S8300EBRSUnplugging the Mains Lead When not in USEInstallation Location Condensation is the Enemy of Video RecordersFeatures ContentsFeatures and Functions Front ViewFluorescent display Fluorescent Display RECFeatures and Functions Reset buttonRear View Sensor Connecting with Other EquipmentSetting the Menus Present time display will appearPresent Time Display Timer Program DisplayTime Date Search Setting the Menus Recording SET UPRear Terminal Maintenance First Time SET UP Setting the Present Time Display modeFRI Setting the Present Time to the Exact Second Setting the Present TimePreventing Accidental Erasure Loading and Unloading the Cassette TapeLoading UnloadingRecording Check Function REC ModeLock Mode Manual RecordingRecommended Number of Tape USE Stop Rewind Repeat AlarmprotRepeat Recording Number of Tape USE Repeat REC TimesConnection Manual RecordingONE SHOT/INTERVAL Recording Synchronous RecordingAdditional Features Timer Recording Symptom Fault Action Order to Avoid Mistakes When Using the Timer1st VCR Alarm RecordingAlarm Recording Connection External Time Clock AdjustmentEmergency Recording Setting for Alarm RecordingIndex Search Alarm RecordingAlarm Record Time Display Locating the Start of Alarm RecordingsPlayback Mode PlaybackAudio Playback Still Picture Special Effects PlaybackShuttle Ring Direct Shuttle RingWhen the picture is vibrating Adjustment During PlaybackTracking Adjustment Picture Quality AdjustmentUsing with the Personal Computer Configuring the Time Lapse VCRConnecting the VCR to a personal computer Setting Stop BIT Length RS-232C SettingSetting Transmission Rate Setting Data BIT LengthPhysical protocol of RS-232C Using with the Personal ComputerConnecting to a Personal Computer Data Communications SettingsCommand carried out Command Commands sent to the VCR FormatPower on command Command receivedCommand carried out VCR02 Command ParameterCommand for fast forwarding VCR02 Command received VCR02Commands and Responses 171=TIME Date Adjust + STOP=0, REWIND=1, REPEAT=2 +0=SERIES, 1=REC-START/STOP =SYNC REC Error codesDisplay Self Diagnostic FunctionFluorescent Monitor Cause Remedy To Turn OFF the IndicationBefore Calling for Service Symptom RemedyIs the Lock indicator illuminated? Control INPUT/OUTPUT Signals and Circuits Control INPUT/OUTPUT Signals and Circuits CircuitLabel B-7 Connectors Specifications872C193C3