Hitachi CMP307XU manual Switching the Display Method, Sq.W

Page 26

ENGLISH

OTHERFEATURES (continued)

Switching the Display Method

The display method can be switched by changing the settings of the display area (when the RGB input jack is selected) or display size (when the Video input jack is selected).

Switching when the RGB input jack is selected

Input signal ( 30 )

Display area setting (DISPLAY AREA)

(Resolution)

NORMAL (normal number of pixels)

FULL (expanded number of pixels)

 

 

 

640 x 400

640 x 400

 

 

 

 

640 x 480

640 x 480

1024 x 7681)

 

 

800 x 600

800 x 600

 

 

 

 

832 x 624

832 x 624

 

 

 

 

1024 x 768

1024 x 768

 

 

 

1280 x 1024

1024 x 7682)(Squeezed display, partial display)

 

 

 

1)The expanded processing method ( 20 INTERPOLATION) becomes effective.

2)The display status and display area is changed each time the SELECT button is pressed, or

each time the or keys of the remote control are pressed. (Refer to 19 Display Area) Display may not be correct in some cases, depending on the signal conditions.

 

HINTS

 

 

To maximize display performance, it is recommended that the 1024 x

 

 

 

 

 

 

768 (vertical frequency 60Hz) input signal specifications be used.

 

 

 

 

 

 

 

 

Switching when the Video Input jack is selected

 

This setting is used

When it is desired to

When it is desired to

When it is desired to

 

slightly enlarge images

Problem

normally.

when black stripes

view a Squeeze signal

slightly enlarge a

image.

Squeeze signal image.

 

 

appear at the top and

 

 

 

 

 

 

bottom of the screen.

 

 

Display size setting

NORMAL

WIDE

SQ.N

SQ.W

 

 

 

 

(DISPLAY SIZE)

Normal display

Enlarge the entirety

Vertical compression

Enlarge horizontally

 

 

4:3 signal

4:3 signal

Squeez signal1)

Input signal

 

 

 

 

Display screen

 

 

 

 

 

 

All four edges of the

 

The left and right side

 

 

screen are missing.

 

of the screen are

Remarks

 

Adjust the horizontal

 

missing.

 

and vertical positions

 

Adjust the horizontal

 

 

 

 

 

19 when text is

 

position 19 when text

 

 

missing.

 

is missing.

1)The video signal when a screen with an aspect ratio (the ratio between the sides and width of the screen) of 16: 9 is compressed to 4: 3.

*

indicates signals and

 

indicates screens in the chart above

24

Image 26
Contents Plasma Inch High Definition Plasma Display Features Large-screen, high-definition plasma display panelContents Safety Guidelines Be careful of power cord connection Do not damage or modify the power cordEnclosed power cord must be used Do not touch the power plug when lightning is close to youDo not bundle the power cord When you disconnect the power plugDo not put the monitor in high temperature atmosphere Remove the power cord for complete isolationPrecautions FCC Federal Communications Commission Statement WarningInstallation Instructions Installation Instructions Component NamesRear Installation and Cabling Connecting to the PC Monitor rear panelConnecting to Video Equipment Video equipmentDegrees degrees About 5m Handling the Remote ControllerLoading Batteries Operating Instructions Turning Power On and OffIndicating lamp Power status Input Selection Volume AdjustmentVolume Sub inputAdjustment status guidance Contrast AdjustmentInput Signal Status Display Sound MutePicture Menu Contrast On-Screen Display System, EasyMenuMain Menu Picture Sound Display Function BrightnessAdjustment Item List Menu item Selected Adjustment Setup hintTint Mute VolumeColor SharpnessMenu item Selected Adjustment English NTSC,PAL,SECAMDo not select when Select when Setting an unusedSets to Skip Sets to Select Accelerate switching Switching inputsDisplay Registration condition Other FeaturesAutomatic Store Display menu item Reset Settings InitializationSignal Check Status Display ExampleSwitching the Display Method SQ.WPower Save Mode Sound ModeSymptom Point to check TroubleshootingSymptoms That Seemingly Appear to be Failures Display image appears flowing display 2 RGB input SymptomFine pattern flickers when displayed on the screen display ExampleProduct Specifications General SpecificationsSync signal type Priority Signal InputPin Input signal GNDHorizontal Dot clock Remarks Recommended Signal ListResolution XGA