BenQ MX501-V, MS500-V user manual Controls and functions, Projector

Page 10

Controls and functions

Projector

1

28 9

3

8.	TEMPerature warning light
	Lights up red if the projector's
	temperature becomes too high.
9.	POWER indicator light
	Lights up or flashes when the projector is
	under operation.
10.	AUTO

4

5

6

7

1.Focus ring

10 11 12

13

14 11

Automatically determines the best picture
timings for the displayed image.
11. Keystone/Arrow keys ( / Up,	/
Down)
Manually corrects distorted images
resulting from an angled projection.

Adjusts the focus of the projected image.

2.Zoom ring

Adjusts the size of the image.

3.LAMP indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem.

4.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

5. Left/

Decreases the projector volume.

6.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

7.BLANK

Used to hide the screen picture.

12.		POWER


	Toggles the projector between standby
	mode and on.
13.		Right/

Increases the projector volume.

When the On-Screen Display (OSD) menu is activated, the #5, #11, and #13 keys are used as directional arrows to select the desired menu items and to make adjustments.

14.SOURCE

Displays the source selection bar.

10 Introduction

Image 10

Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the frontFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalStarting up the projector OperationOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Switching input signalChanging the password Enter a new passwordSelecting the aspect ratio Magnifying and searching for detailsTo select the source About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioOperation Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen only for MX501/ MX501-V Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMain menu Sub-menu Options Menu operationMenu system BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Panel KeyLock SplashBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternSystem CurrentStatus Maintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Vertical HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer