BenQ MX501-V Indicators, Light Status & Description Power events, Lamp events, Thermal events

Page 50

Indicators

Light

Status & Description

					Power events

	Off	Off	Orange	Stand-by mode.
	Off	Off	FlashingGreen	Powering up.
	Off	Off	Green	Normal operation.
				• The projector needs 90 seconds to cool down as it was
					abnormally shut down without the normal cooling down
					process.
	Off	Off	Orange	• The projector needs to cool for 90 seconds after the power
	Off	Off	Flashing		is turned off.
			Flashing		is turned off.
				• The projector has shut down automatically. If you try to re-
					start the projector, it will shut down again. Please contact
					your dealer for assistance.

					Lamp events
	Red	Off	Orange	The projector has shut down automatically. If you try to re-
	Red	Off	Flashing	start the projector, it will shut down again. Please contact your
				dealer for assistance.
	Red	Off	Off	1.	The projector needs 90 seconds to cool down. Or
	Red	Off	Off	2.	Please contact your dealer for assistance.
				2.	Please contact your dealer for assistance.

Thermal events

Off	Red	Off
Red	Red	Off
Green	Red	Off
Orange	Red	Off
Red	Red	Red
Green	Red	Red
Orange	Red	Red
Red	Red	Green
Green	Red	Green
Orange	Red	Green
Red	Red	Orange
Green	Red	Orange
Orange	Red	Orange
Red	Green	Off
Green	Green	Off

The projector has shut down automatically. If you try to re- start the projector, it will shut down again. Please contact your dealer for assistance.

50 Maintenance

Image 50

Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the frontFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalOperation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signalChanging the password Enter a new passwordTo select the source Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioOperation Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMain menu Sub-menu Options Menu operationMenu system BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Panel KeyLock SplashBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternStatus CurrentSystem Maintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Vertical HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer