BenQ MS500-V Switching input signal, Changing the password, Disabling the password function

Page 23

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.

2.Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.

3.Enter the old password.

i.If the password is correct, another message “INPUT NEW PASSWORD” displays.

ii. If the password is incorrect, the password error message displays lasting for three seconds, and the message “INPUT CURRENT PASSWORD” displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. Press MODE/ENTER. The message “INPUT PASSWORD” displays. Enter the current password.

i.If the password is correct, the OSD menu returns to the Security Settings page.

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

Press to highlight Splash Screen Lock and press / to select Off. The Splash Screen function in the SYSTEM SETUP: Basic menu will be available for your change.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message “INPUT PASSWORD” displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

Operation 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MX501/MS500/MX501-V/MS500-V Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functionsRemote control Operating the projector from the front Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation OperationStarting up the projector Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menuHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Switching input signalChanging the password Disabling the password functionTo select the source Magnifying and searching for detailsSelecting the aspect ratio Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioOperation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projector Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneOnce the cooling process finishes, a Power Off Ring Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus CurrentSystem Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartVertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents