BenQ MX501-V, MS500-V user manual Use the handle to slowly pull the lamp out Projector

Page 48

8.Use the handle to slowly pull the lamp out of

the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

9. As shown in the figure, lower the new lamp.

10.	Reconnect the lamp connector to the
	projector.
11.	Tighten the screw that secures the lamp.	3
12.	Ensure the handle is fully laid flat and locked	3
	in place.	2
	in place.
•	Loose screw may cause a bad connection, which	1
	could result in malfunction.

• Do not over tighten the screw.

13.Replace the new protection film that comes with the new lamp.

14.Replace the lamp cover on the projector.

2

2

1

15.Tighten the screw that secures the lamp cover.

•Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

48 Maintenance

Image 48

Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Operating the projector from the frontPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalOperation Starting up the projectorOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Switching input signal Changing the passwordDisabling the password function Enter a new passwordMagnifying and searching for details Selecting the aspect ratioTo select the source Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioOperation Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen only for MX501/ MX501-V Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMenu operation Menu systemMain menu Sub-menu Options BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description TeachingSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key LockBackground SplashSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternCurrent SystemStatus Maintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Vertical HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer