BenQ MX501-V, MS500-V user manual Specifications, Projector specifications

Page 52

Specifications

Projector specifications

All specifications are subject to change without notice.

Optical

Resolution (MX501/MX501-V)

1024 x 768 XGA (MS500/MS500-V)

800 x 600 SVGA

Display system 1-CHIP DMD

Lens F/Number

F= 2.56-2.8 Lamp

220 W lamp

Electrical

Power supply

AC100–240V, 3.2 A, 50-60 Hz (Automatic) Power consumption

322 W (Max); < 1 W (Standby)

Mechanical

Weight

2.4 Kg (5.29 lbs)

Output terminals

RGB output

D-Sub 15-pin (female) x 1 Speaker

(Stereo) 2 watt x 1 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 1

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Audio signal input Audio in

PC audio jack x 1 USB port (Mini-B x 1)

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

52 Specifications

Image 52

Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Operating the projector from the frontPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalStarting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Switching input signal Changing the passwordDisabling the password function Enter a new passwordSelecting the aspect ratio Magnifying and searching for detailsTo select the source Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioOperation Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen only for MX501/ MX501-V Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMenu operation Menu systemMain menu Sub-menu Options BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description TeachingSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key LockBackground SplashSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternSystem CurrentStatus Maintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Vertical HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer