BenQ MX501-V, MS500-V user manual Description of each menu

Page 38

Description of each menu

1. DISPLAY menu

Function

Description

Wall Color

Corrects the projected picture’s color when the projection surface is not

white. See "Using Wall Color" on page 27 for details.

 

 

 

Aspect Ratio

There are several options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 24 for

 

details.

 

 

Keystone

Corrects any keystoning of the image. See "Switching input signal" on

page 23 for details.

 

 

 

 

Displays the position adjustment page. To move the projected image,

 

use the directional arrow keys. The values shown on the lower position

Position

of the page change with every key press you made until they reach their

maximum or minimum.

 

This function is only available when a PC signal (analog RGB) is

 

selected.

 

Adjusts the clock phase to reduce image

 

distortion.

Phase

 

 

This function is only available when a PC

 

signal (analog RGB) is selected.

H. Size

Adjusts the horizontal width of the image.

This function is only available when a PC signal (analog RGB) is

 

selected.

Digital Zoom

Magnifies or reduces the projected image. See "Magnifying and

searching for details" on page 24 for details.

 

 

 

 

This projector features a 3D function which enables you to enjoy the

 

3D movies, videos, and sporting events in a more realistic way by

 

presenting the depth of the images. You need to wear a pair of 3D

 

glasses to view the 3D images.

 

• Only for PC type signal:

3D Sync

When the vertical frequency is 120Hz, and the content being projected

is made with 3D technology, selecting Frame Sequential will present the

 

3D images.

 

When the 3D Sync function is on:

 

• The brightness level of the projected image will decrease.

 

• The Picture Mode cannot be adjusted.

 

• The Keystone can only be adjusted within limited degrees.

 

 

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

38 Operation

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the frontFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio Component Video Better Good NormalOperation OperationStarting up the projector Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Disabling the password function Switching input signalChanging the password Enter a new passwordTo select the source Magnifying and searching for detailsSelecting the aspect ratio About the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioOperation Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Remote paging operationsFreezing the image Locking control keysCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMain menu Sub-menu Options Menu operationMenu system BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description TeachingSettings System Setup Basic menu Function Description Quick AutoTimer SearchBackground Panel KeyLock SplashBaud Rate System Setup Advanced menu Function DescriptionReset All Test PatternStatus CurrentSystem Maintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputTiming Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Vertical HorizontalCopyright Warranty and Copyright informationLimited warranty Disclaimer
Top Page Image Contents