BenQ MX501 Confined. Allow at least 50 cm clearance, If the ventilation holes are seriously

Page 5

Safety Instructions (Continued)

13.Do not place this projector in any of the 14. Do not block the ventilation holes.

following environments.

- Do not place this projector on a blanket,

- Space that is poorly ventilated or

bedding or any other soft surface.

- Do not cover this projector with a cloth

confined. Allow at least 50 cm clearance

from walls and free flow of air around

or any other item.

the projector.

- Do not place inflammables near the

- Locations where temperatures may

projector.

become excessively high, such as the

 

inside of a car with all windows rolled

 

up.

 

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.

 

If the ventilation holes are seriously

 

obstructed, overheating inside the

 

projector may result in a fire.

15.

Always place the projector on a level,

 

horizontal surface during operation.

 

- Do not use if tilted at an angle of more

- Locations near fire alarms

than 10 degrees left to right, nor at angle

- Locations with an ambient temperature

of more than 15 degrees front to back.

above 40°C / 104°F

Using the projector when it is not fully

- Locations where the altitudes are higher

horizontal may cause a malfunction of,

or damage to, the lamp.

than 3000 m (10000 feet).

 

3000 m

 

(10000 feet)

 

16.

Do not stand the projector on end

0 m

vertically. Doing so may cause the

(0 feet)

projector to fall over, causing injury or

 

resulting in damage to the projector.

Important safety instructions

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents MX501/MS500/MX501-V/MS500-V Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functionsRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Operating the projector from the frontChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalOperation OperationStarting up the projector Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Below is the overview of the OSD menuUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the password Switching input signalDisabling the password function Enter a new passwordTo select the source Magnifying and searching for detailsSelecting the aspect ratio Adjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioOperation Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionFreezing the image Remote paging operationsHiding the image Locking control keysCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Adjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Shutting down the projectorOnce the cooling process finishes, a Power Off Ring Direct power offMenu system Menu operationMain menu Sub-menu Options BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchLock Panel KeyBackground SplashReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternStatus CurrentSystem Care of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Vertical HorizontalLimited warranty Warranty and Copyright informationCopyright Disclaimer
Top Page Image Contents