BenQ MS500-V Display menu Picture menu Function Description Teaching, Template, Only for, MX501

Page 39

1. DISPLAY menu

2. PICTURE menu

Function

Description

Teaching

Provides several preset patterns for various teaching purposes.

Template

 

(only for

Choose Blackboard or Whiteboard first by pressing / and press

MX501/

/ to choose the pattern you need. Press MODE/ENTER to activate

the pattern.

MX501-V)

 

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 27 for details.

 

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 27 for

 

details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on page

28 for details.

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 28 for details.

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a video

Color

image. See "Adjusting Color" on page 28 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

Adjusts the red and green color tones of the image. See "Adjusting Tint"

Tint

on page 28 for details.

This function is only available when a Video or S-Video signal is

 

 

selected and the system format is NTSC.

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 28 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

Brilliant Color

See "Adjusting Brilliant Color" on page 28 for details.

 

 

Color

See "Selecting a color temperature" on page 28 for details.

Temperature

 

 

 

3D Color

See "3D Color Management" on page 29 for details.

Management

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

 

Operation 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents MX501/MS500/MX501-V/MS500-V Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Controls and functionsRemote control Operating the projector from the front Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation Starting up the projectorOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menuHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Enter a new password Switching input signalChanging the password Disabling the password functionMagnifying and searching for details Selecting the aspect ratioTo select the source Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioOperation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Operating in a high altitude environmentCreating your own startup screen only for MX501/ MX501-V Shutting down the projector Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneOnce the cooling process finishes, a Power Off Ring Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateCurrent SystemStatus Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartVertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents