BenQ MS500-V, MX501 Supported timing for Component-YPbPrinput, Timing, Vertical Horizontal

Page 55

Supported timing for Component-YPbPrinput

Timing

Resolution

Vertical

Horizontal

Pixel Frequency

Frequency (Hz) Frequency (kHz)

(MHz)

 

 

480i

720 x 480

59.94

15.73

13.5

480p

720 x 480

59.94

31.47

27

576i

720 x 576

50

15.63

13.5

576p

720 x 576

50

31.25

27

720/50p

1280 x 720

50

37.5

74.25

720/60p

1280 x 720

60

45.00

74.25

1080/50i

1920 x 1080

50

28.13

74.25

1080/60i

1920 x 1080

60

33.75

74.25

1080/24P

1920 x 1080

24

27

74.25

1080/25P

1920 x 1080

25

28.13

74.25

1080/30P

1920 x 1080

30

33.75

74.25

1080/50P

1920 x 1080

50

56.25

148.5

1080/60P

1920 x 1080

60

67.5

148.5

Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.

Supported timing for Video and S-Video inputs

Video mode

Horizontal

Vertical Frequency

Color sub-carrier

Frequency (kHz)

(Hz)

Frequency (MHz)

 

NTSC

15.73

60

3.58

PAL

15.63

50

4.43

SECAM

15.63

50

4.25 or 4.41

PAL-M

15.73

60

3.58

PAL-N

15.63

50

3.58

PAL-60

15.73

60

4.43

NTSC4.43

15.73

60

4.43

Specifications 55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents MX501/MS500/MX501-V/MS500-V Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functionsRemote control Operating the projector from the front Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menuHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Enter a new password Switching input signalChanging the password Disabling the password functionSelecting the aspect ratio Magnifying and searching for detailsTo select the source Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioOperation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeCreating your own startup screen only for MX501/ MX501-V Shutting down the projector Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneOnce the cooling process finishes, a Power Off Ring Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateSystem CurrentStatus Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartVertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright
Top Page Image Contents