BenQ MS500-V, MX501-V user manual Remote control

Page 11

Remote control

7

1

8

2 9

3	10
3
4	11
5	12
	8
6	13
6
	14
	15

1. POWER

Toggles the projector between standby mode and on.

2. Freeze

Freezes the projected image.

3. Left

4.BLANK

Used to hide the screen picture.

5.Digital Zoom (+, -)

Magnifies or reduces the projected picture size.

6.Volume +/-

Adjusts the sound level.

7.MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

8.Keystone/Arrow keys ( / Up, /

Down)

Manually corrects distorted images resulting from an angled projection.

9.AUTO

Automatically determines the best picture timings for the displayed image.

10. Right

When the On-Screen Display (OSD) menu is activated, the #3, #8, and #10 keys are used as directional arrows to select the desired menu items and to make adjustments.

11.SOURCE

Displays the source selection bar.

12.MODE/ENTER

Selects an available picture setup mode.

Activates the selected On-Screen Display (OSD) menu item.

13.Timer On

Activates or displays an on-screen timer based on your own timer setting.

14.Timer Set up

Enters presentation timer setting directly.

15.PAGE UP/PAGE DOWN

Operate your display software program (on a connected PC) which responds to page up/down commands (like Microsoft PowerPoint).

Introduction 11

Image 11

Contents MX501/MS500/MX501-V/MS500-V Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Controls and functionsRemote control Operating the projector from the front Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation OperationStarting up the projector Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusFollowing example describes how to set the OSD language Use / to highlight the System Setup Basic menuHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Switching input signalChanging the password Disabling the password functionTo select the source Magnifying and searching for detailsSelecting the aspect ratio Screen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioOperation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownLocking control keys Remote paging operationsFreezing the image Hiding the imageCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projector Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneOnce the cooling process finishes, a Power Off Ring Direct power offBasic Menu operationMenu system Main menu Sub-menu OptionsMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus CurrentSystem Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartVertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright