BenQ MX501-V, MS500-V user manual Shipping contents

Page 8

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

*The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.

Projector

Power cord

VGA cable

Quick start guide

User manual CD

Warranty card*

Remote control with battery

Pull the tab before using the remote control.

Optional accessories

Spare lamp kit

RS232 cable

2.Ceiling mount kit

8 Introduction

Image 8

Contents Welcome MX501/MS500/MX501-V/MS500-V Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Controls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteryPull out the battery holder Operating the projector from the frontPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeConnection ConnectionConnecting video source devices Connecting audioTerminal name Terminal appearance Component Video Better Good NormalOperation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Below is the overview of the OSD menuUsing a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Switching input signal Changing the passwordDisabling the password function Enter a new passwordTo select the source Magnifying and searching for detailsSelecting the aspect ratio Projectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioOperation Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Freezing the imageHiding the image Locking control keysCreating your own startup screen only for MX501/ MX501-V To activate the High Altitude ModeOperating in a high altitude environment Adjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Shutting down the projectorDirect power off Once the cooling process finishes, a Power Off RingMenu operation Menu systemMain menu Sub-menu Options BasicMain menu Sub-menu Options System Setup Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description TeachingSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key LockBackground SplashSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternStatus CurrentSystem Maintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Use the handle to slowly pull the lamp out Projector Time will be reset to Connect the power and restart the projectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Vertical HorizontalWarranty and Copyright information Limited warrantyCopyright Disclaimer