Sanyo DSR-3506P manual Recording, Alarm recording, Set alarm recording, End alarm recording

Page 21

3RECORDING

POWER indicator ALARM FULL indicator

[EXIT] button

[REC/STOP] button				[TIMER] button

OPERATION

Alarm recording

Use the following procedure to automatically record alarm video to the alarm recording area when an alarm signal is detected.

Recording will not be possible until a time has been set for the digital video recorder. Make sure to set the time. (JP.14)

1 Set alarm recording.

Follow the instructions on P.68 set “7. ALARM REC MODE SET” from <RECORD SET>.

2 Press the [EXIT] button.

The setting procedure is ended and the normal screen is displayed.

EXIT

When an alarm signal is detected

zWhen an alarm signal is detected, “ALARM” flashes in the operation display and the alarm recording starts (indicated by “REC”).

zAlarm video is recorded to the alarm recording area.

zWhenever an alarm occurs, the number of alarms as indicated in the operation display is incremented.

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000	Counts the number
	of alarms.
	Values between
	0000 and 9999 can
	be displayed.

02

zIf an alarm occurs during normal recording or timer recording, the recording operation will be ended.

zA maximum of 16,000 alarm recordings can be made on one hard disk. If hard disk expansion is carried out, this number can be increased to 32,000. Note, however, since settings for each condition will affect the maximum number of recordings that can be made, be sure to check menu settings and display content.

3 End alarm recording.

When the alarm duration has expired (default setting: 20 seconds), both “REC” and “ALARM” finish flashing from the operation display and recording stops.

zWhen the space remaining in the alarm recording area drops below a preset value, the FULL indicator on the digital video recorder’s front panel starts to flash. If recording is continued beyond this point, the alarm recording area will become full, recording will stop, and the FULL indicator will stop flashing and remain lit. In such a case, use the <RECORDING AREA SET> menu to perform “AREA FULL RESET” for the alarm recording area, thus allowing recording to start again from the beginning. (JP.60)

20

English

Image 21

Contents Page Service PrecautionLocation Avoiding Electrical Shock and FireAccessories Main featuresSymbols used in this manual IntroductionContents Other Contents SettingsBefore USE „ Notes on replacing the HDD„ Handling a detached HDD unit Before USE Backup batteryHard disk and cooling fan are consumable components Important recordingsFront panel Names and Functions of PartsNames and Functions of Parts Rear panel Connecting an amplifier Installation and ConnectionsConnecting Alarm in terminals Basic connectionsConnecting Sensor Alarm OUT terminals Installation and ConnectionsConnecting control terminals Connecting the power cord01-01-04 000000 REC Reperat EN a Alarm Preparing for USEOperation display area Changing the position of the operation display area Preparing for USEChanging the language Press the OSD button several timesExample Setting 830 on 22 May Setting the timeTurn the shuttle dial clockwise Press the Exit buttonPreparing for USE The internal hard disk Alarm recording areaHard disk recording areas Normal recording areaViewing on a full screen Viewing Video from a CameraViewing on multiple screens Press the No Camera Select buttonViewing with automatic screen selection Viewing Video from a CameraPress the Multi button Press the Sequence buttonSet MON.2 Display from Alarm Operation SET to ON. JP.74 Viewing on the monitorPress the MON2 button Press the Timer button Timer recordingRecording Normal recordingSet alarm recording Alarm recordingEnd alarm recording When an alarm signal is detectedSet pre-alarm recording Pre-alarm recordingAfter entering the setting, press the Exit button If an alarm is detectedPlaying video on a full screen PlaybackFast-forward and fast-rewind playback Changing the playback speedEnlarging the playback video PlaybackPress the Zoom button during playback Move the zoom frame to the area to be magnifiedPerforming frame advance forward or reverse Viewing still imagesPress the Zoom button Press the Still button during playbackPlaying video on multiple screens Press the Quad button during playbackPress the Multi button during playback Searching for Recorded Video Press the appropriate Alarm button during playback Alarm search„ To view pre-alarm video To view alarm video before or after the current playbackAlarm number for the selected recording will start to flash Alarm thumbnail searchTime/date search Turn the jog dial to select TIME/DATE SearchRecording END Recording TOPChannel SearchArchive area search Search indicator lights and Search screen is displayedMotion detection search Turn the jog dial to select the video for playbackStart Example Normal Cursor moves to ChannelEND Motion SensorSet the motion sensor to use for searching Motion sensor setting screen is displayedOFF flashes ‹OFFCarry out motion sensor setting again „ If not FOUND! is displayedDisplay returns to the Motion Detection Search screen Saving Copying Recorded Video Copying video to the hard disk’s archive area JP.35Copying video to a CompactFlash card or Microdrive JP.36 Copying video to the hard disk’s archive area Saving Copying Recorded VideoPress the Copy button Example Copying a specified 10-second portion of videoTurn the jog dial to select Seconds „ To cancel a copy operationInsert a CompactFlash card Insertion method Removal methodArchive Area flashes Copy screen is displayedFormatting a CompactFlash card Viewing images copied to a CompactFlash card on a PCJpeg images Images copied to a CompactFlash cardMoving from the Main Menu to a sub-menu or setting screen Menu Configuration and OperationsBasic menu operations Turn the jog dial to select a menuMenu Configuration and Operations Restoring menu setting items to their default valuesMovement and confirmation in sub-menus and setting screens Sub-menu configuration Main menu Turn the jog dial to select the item toBe set, and then turn the shuttle dial Clockwise Multi Screen JP.87 Sub menu Setting item Settings or display contentSequence SET Color Level JP.93Setting the summer time Initial settingsInitial SET is used to make the following setting Initial SETTurn the jog dial to change the settings When USE is selected for Summer Time SETInitial SET Cursor moves to the month External clock settingCursor moves to the time To C Terminal To Clock SET in terminalExample Detecting connected camerasExample Setting the title HALL-1F for Camera No Setting camera titlesFirst position for title setting flashes Turn the jog dial to select HExample Setting 17 November as a holiday Setting holidaysSet the day and month for item No Turn the shuttle dial clockwise after settingMonth DaySetting time periods Example 1 Setting periods using Time Period a Timer period settingsTime Period a settings Set T1 to 6 AM Time Period B settings Set T1 to 6 AMTime period operations settings Time Period a flashesCursor moves to Mask Performing easy setup Settings for recordingRecord SET is used to make the following settings Record SETEasy Setup screen is displayed Setting based on recording daysCursor moves to Timer Recording DAY Record SETDisplay returns to the Easy Setup screen Example on Settings ‹ indicates the default settingSet Picture Quality Set Audio RecordingSetting based on recording rate Displaying the recording areas AlarmSee P.55 Recording Area SET screen is displayedChanging recording areas „ Default hard disk settings„ Recording area allocations „ If the normal recording area is set to 0%Setting overwrite permission Setting recording conditions No on the Warning screen flashes FlashingOn flashes Setting auto deleting Turn the jog dial to select the storage period01-01-04 000000 REC 1% Setting normal recording Turn the shuttle dial clockwise Press the Exit buttonClockwise Set REC Rate Setting program recordingSet REC Program Group ProgramCursor moves to 01 from Serect Individual Camera Rate FPS Recording rate flashesVideo from Camera No will not be recorded Timer settings Timer setting itemsStart „ Picture quality and recording rate for timer recording „ To change a displayed setting itemTo cancel all set timer reservations Timer reservations spanning more than 24 hoursTimer recording using an external timer Make settings in the Week and Start columnsOFF for Program flashes For FPS flashesTo set alarm recording Setting alarm recordingDial clockwise OFF flashesOperates while an alarm is being triggered sec. minimum Maximum number of alarm recordingsSet REC Rate and Duration Recording pattern for SW and onlyTo set pre-alarm recording When alarm recording settings have been completedREC Rate for PRE-ALARM Recording flashes Cursor moves to recording rate and durationSetting the alarm trigger When pre-alarm recording settings have been completedDefault setting 1 MIN Cursor moves to Alarm Trigger Use this setting to indicate how alarms are to be detectedUse this procedure to set other sensor positions Setting the motion sensorsPress the Camera Select button LevelCursor moves to Level Flashes for the ModeOFF flashes for Level To BOFF flashes in the Alarm Retrigger field Setting alarm operation and displayExample Alarm „ To stop motion sensor recordingCanceling alarms Setting alarm displayCursor moves to Alarm Priority Setting data display General settings01-01-04 000000 REC 1% EN a Alarm General SETSetting display for video loss General SETPerform the following if so required Alarm default setting OFF Setting the buzzerDisk Full default setting on Disk Error default setting onUse the same procedure to set 123456AB Setting the security lock„ Operation after setting passwords Setting the administrator passwordTurn the jog dial to select on Following this, turn the shuttle dial clockwiseTurn the jog dial clockwise Then turn the shuttle dial clockwiseSetting the security lock Setting and initializing the hard diskCanceling the security lock Initializing the hard diskNetwork settings Expanding the hard disk capacityMaking network connections Connecting to an intranet using a hub Making network settingsNetwork SET screen is displayed OFF flashes for Network ControlSet Subnet Mask Set IP AddressSet Gateway Set PortEnter the password using the shuttle dial and jog dial Setting RS-485General SET screen appears Cursor moves to Status InfoNormal screen Setting procedure is ended and the display returns to‹DATA SpeedSetting quad positions Setting quad and multi 6 displayScreen SET Example Displaying Camera No in quad positionScreen SET Setting multi 6 positionsChecking modified screen positions Changes to1S flashes for Full Example Automatic switching of a full screen every 5 secondsSetting the main monitor and monitor Specify Time Period a and Time Period BMAIN/MON.2 Monitor SET screen is displayed Starts to flash for the time period Cursor moves to Mask SET Setting masksMask SET screen is displayed Starts to flash for Time PeriodSetting the color level OFF flashes Settings ‹ indicates the default settingColor Level SET screen is displayed ‹AUTO Auto flashesFAILURE/RECOVER Power FAILURE/USED TimePower DISK1 USEInitialized Record AreaOperation class Saving menu settings on a CompactFlash card Copy Menu SettingsSave Menus to CF Load Menus from CFLoading settings from a CompactFlash card Copy Menu SettingsWhen copying recording area settings Turn the jog dial to select LoadInterface Specifications RS-485 specificationsRS-485 termination switch settings DVR/VCR command table Interface SpecificationsSpecifications SpecificationsJpeg XXXSpecifications DimensionsUnits mm 364.5 420 349 Table of recording rate and times „ Example Recording to a 80 GB hard disk 100%-usage„ Example After expansion to 160 GB 100%-usage „ Example After expansion to 300 GB 100%-usage 104Program recording rate Table of recording rate settingsTable of pre-alarm recording times Minutes 10s 20s 40sFPS field/sec Menu Setting Sequence Normal REC Mode SET →P.62Title SET →P.47 Menu Setting Sequence HDD SET →P.81 Mask SET →P.92RS-485 SET →P.85 Index Index Time/date search Timer recording Timer settings

Related manuals

Manual 48 pages 56.38 Kb