Winegard RD-9946 installation manual Rev /98

Page 10

8.After feeding cable to where you are going to install the positioner, strip 3/8" insulation off all wires in the 13 cable bundle.

9.Attach wires as shown in Figure 11 to the 13 pin connector supplied. Double check that wires will not pull out and that wire colors are correct.

NOTE: The first color is the primary color of the wire. Example; Red/

White, means that the wire is red with a white stripe.

	Screws used to
13 Pin Connector	secure connector
	to positioner.
Green/Black	Blue
Red/Black	White
Red/White	Black/White
Green	Orange/Black
Red	White/Black
Black	Blue/Black
Orange

Figure 11

10.You are now ready to connect the mount to the positioner and the positioner to the receiver, see Figures 12 and 13. Make sure there is adequate ventilation. The positioner and the receiver produce heat.

NOTE: When connecting the 13 pin connector to the rear of positioner make sure to secure connector to positioner using the screws on the connector.

CAUTION

DO NOT CONNECT EITHER THE POSITIONER OR RECEIVER TO AC

POWER UNTIL ALL CONNECTIONS HAVE BEEN MADE. BOTH UNITS

ARE ON AS SOON AS THEY ARE CONNECTED TO POWER.

Rev. 6/98

10

Image 10

Contents Winegard Important Safeguards Not applicable to mount and antennaTable Of Contents Unpacking/InventoryInstallation Requirements Rev 9/98 Installation Satellite System, RD-9946 proceed to stepDo not Caulk Mount Base Ring Page Rev /99 Rev /98 Optional RD-9911 Warning Device Refer to , Page 14 for operation and installationSilver Connecttoignition+12VDCCH 3/4 OUT To Receiver Control Wires To AntennaSensar TV Antenna Receiver PositionerPress Select a or B as appropriate Park Move to Last SatSearch DSS Park Press UP/DOWN arrow buttons to get Park on screenRD-9901 Remote Control Wall Plate Telephone Cord RD-9901 Remote Control Wall Plate InstallationPositioner Rear Panel Connect to vehicle ground RD-9911 Warning Device Installation/OperationRCA cable Install two AA batteries provided Connect to ignition +12 VDCQTY Cable Roof-thru Plate InstallationDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents For Programming information call Dish Network Uplink Signal Programming Uplink Control CentersIntroduction / HOW does Digital Satellite TV WORK? DSSSelect a City Enter Elevation Finding the Satellite Method Using the City MenuSystem Operation Finding the Satellites Press Select aPress Left arrow button to scroll list to the last Start Search QuitCalculating Entry of the previous stateMoving to Start Setting DetectorFine Tuning Azimuth Searching Level =Correct Satellite Continue Search Fine Tuning ElevationSystem has found a satellite and is fine tuning the signal Press Select a if correct satellite was foundFinding the Satellite Method Entering the Elevation Press Select B Enter elevation, FigureEl Angle = Press Select B if correct satellite was not foundPress UP arrow button Enter Elevation Enter LocationPress Select B Press Select B Enter Location, FigurePress Left arrow button Latitude =Longitude = To decrease latitude by 1oLatitude and longitude Putting Antenna in Park Position Move to Last Satellite Move to Last Sat Manual MoveManual Move Edit Manual MovementAz3 = El 3 = XXX Enter Code Edit MenuEdit Search DSS Press Select a to enter code101.0 Select Search SatelliteSelect Search Sat Set Motor Positions EditInactive Edit Add/Edit Search SatelliteQuit Press Select a to enter satellite into memory Winegard* 165.0 QuitWinegard* 165.0 Edit Press Select a to enter new satellite as search satellitePage Search routine again Remote Panel OperationSearch For Satellite SatelliteParking the Antenna Page Pinnacle Positioner Positioner Controls & Indicators Switch was removed 2/16/98Programmed City Locations Power Environmental ConditionsWinegard Important Safeguards Introduction Antenna Reflector at Look angle No Satellite FoundLnbf Coax Center Conductor Return To Defaults Memory Restored Press Any Key Test Functions Return to DefaultsSet to Defaults Quit Press Select a Set to Defaults. See FigureSearch Xxxxxx Park Positioner Does Not RespondPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Press Select B Test Remote Panel Test LNB Test Remote PanelTest Remote Panel Elevation = Press Select a Test Remote PanelPress UP arrow button twice Test Remote Panel Search LED = OnTest Remote Panel Search LED = Off Three timesTest Remote Panel Search Key Pressed Test Remote Panel Park LED = OnTest Remote Panel Park LED = Off Press Right arrow button twiceTest Remote Panel Park Key Pressed Test LNB Press Select a Test LNB Signal level, max. isAntenna = 0 dB Level = Min. isMake sure switch is all Way left or right depending Positioner Does Not Come OnParking System Fail Please Check Parking System, Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Antenna Support Assembly Index Part Description QTY NumberMount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher