Winegard RD-9946 installation manual Xxx

Page 36

Azimuth Stop Condition

Azimuth Count - Numbers changed

according to antenna position

(see note)

 

 

 

 

 

 

 

 

Az(X) = XXXXX

 

 

 

El (X) = XXXXX

XXX

 

 

 

 

 

 

Elevation Stop Condition

Signal Level - This will vary according to received signal

(see note)Azimuth Count - Numbers changed according to antenna position

Figure 28

NOTE: There are five (5) motor stop conditions: 0 - Motor stopped under normal conditions.

1 - Motor stopped because a limit switch was encountered.

2 - Motor stopped because motor count limit was reached.

3 - Motor stopped because s button was pressed on the positioner. 4 - Motor stopped because of elevation/rotation constraints (antenna was physically stopped by an obstruction or other obstacle).

Under normal conditions the stop conditions will be 0, 1, 2, or 3. If you get number 4, refer to Troubleshooting section.

36

Image 36
Contents Winegard Important Safeguards Not applicable to mount and antennaTable Of Contents Unpacking/InventoryInstallation Requirements Rev 9/98 Installation Satellite System, RD-9946 proceed to stepDo not Caulk Mount Base Ring Page Rev /99 Rev /98 Device Refer to , Page 14 for operation and installation SilverOptional RD-9911 Warning Connecttoignition+12VDCTo Receiver Control Wires To Antenna Sensar TV Antenna ReceiverCH 3/4 OUT PositionerPark Move to Last Sat Search DSS ParkPress Select a or B as appropriate Press UP/DOWN arrow buttons to get Park on screenRD-9901 Remote Control Wall Plate Installation RD-9901 Remote Control Wall Plate Telephone CordPositioner Rear Panel RD-9911 Warning Device Installation/Operation RCA cable Install two AA batteries providedConnect to vehicle ground Connect to ignition +12 VDCCable Roof-thru Plate Installation QTYDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents Uplink Signal Programming Uplink Control Centers Introduction / HOW does Digital Satellite TV WORK?For Programming information call Dish Network DSSFinding the Satellite Method Using the City Menu System Operation Finding the SatellitesSelect a City Enter Elevation Press Select aStart Search Quit CalculatingPress Left arrow button to scroll list to the last Entry of the previous stateSetting Detector Fine Tuning AzimuthMoving to Start Searching Level =Fine Tuning Elevation System has found a satellite and is fine tuning the signalCorrect Satellite Continue Search Press Select a if correct satellite was foundFinding the Satellite Method Entering the Elevation Press Select B Enter elevation, FigureEl Angle = Press Select B if correct satellite was not foundEnter Elevation Enter Location Press Select BPress UP arrow button Press Select B Enter Location, FigureLatitude = Longitude =Press Left arrow button To decrease latitude by 1oLatitude and longitude Putting Antenna in Park Position Move to Last Satellite Move to Last Sat Manual MoveManual Movement Manual Move EditAz3 = El 3 = XXX Edit Menu Edit Search DSSEnter Code Press Select a to enter codeSelect Search Satellite Select Search Sat Set Motor Positions101.0 EditAdd/Edit Search Satellite Inactive EditQuit Winegard* 165.0 Quit Winegard* 165.0 EditPress Select a to enter satellite into memory Press Select a to enter new satellite as search satellitePage Remote Panel Operation Search For SatelliteSearch routine again SatelliteParking the Antenna Page Pinnacle Positioner Positioner Controls & Indicators Switch was removed 2/16/98Programmed City Locations Power Environmental ConditionsWinegard Important Safeguards Introduction No Satellite Found Antenna Reflector at Look angleLnbf Coax Center Conductor Return To Defaults Test Functions Return to Defaults Set to Defaults QuitMemory Restored Press Any Key Press Select a Set to Defaults. See FigurePositioner Does Not Respond Search Xxxxxx ParkPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Test LNB Test Remote Panel Test Remote Panel Elevation =Press Select B Test Remote Panel Press Select a Test Remote PanelTest Remote Panel Search LED = On Test Remote Panel Search LED = OffPress UP arrow button twice Three timesTest Remote Panel Park LED = On Test Remote Panel Park LED = OffTest Remote Panel Search Key Pressed Press Right arrow button twiceTest Remote Panel Park Key Pressed Test LNB Signal level, max. is Antenna = 0 dB Level =Press Select a Test LNB Min. isMake sure switch is all Way left or right depending Positioner Does Not Come OnParking System, Fail Please Check Parking System Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Antenna Support Assembly Index Part Description QTY NumberMount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher