Winegard RD-9946 RD-9911 Warning Device Installation/Operation, Connect to vehicle ground

Page 15

RD-9911 Warning Device Installation/Operation

To install the Warning Device, proceed as follows:

1.Connect the gold colored wire of the warning device wire harness to ignition +12 VDC (there is only +12 VDC present when ignition is turned ON) See Figure 17.

2.Connect the silver colored wire to vehicle ground. See Figure 17.

3.Connect other end of wire (end with molded plug) to warning device. See Figure 17.

4.Insert the two "AA" batteries into the warning device.

5.Connect the single RCA cable to the WARNING INDICATOR jack on positioner (see Figure 11). Connect the other end to the warning device. See Figure 17.

NOTE: It is recommended that you place the warning device where it will be visible when you start your vehicle. There is no buzzer, only lights in the device. Velcro is provided to help in the placement of the device.

Operation: A red light indicates that the system is still in the raised position and not ready for travel. Red light goes off when in down position. A yellow light comes on when battery is low. Lights only come on when +12 VDC is applied to warning device.

Positioner Rear Panel

WARNING

INDICATOR

RCA cable

Warning Device

Install two "AA" batteries provided

SILVER

Connect to vehicle ground

 

GOLD

Connect to ignition +12 VDC

 

 

Figure 17

Rev. 6/98

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Winegard Not applicable to mount and antenna Important SafeguardsUnpacking/Inventory Table Of ContentsInstallation Requirements Rev 9/98 Satellite System, RD-9946 proceed to step InstallationDo not Caulk Mount Base Ring Page Rev /99 Rev /98 Connecttoignition+12VDC Device Refer to , Page 14 for operation and installationSilver Optional RD-9911 Warning Positioner To Receiver Control Wires To Antenna Sensar TV Antenna Receiver CH 3/4 OUTPress UP/DOWN arrow buttons to get Park on screen Park Move to Last SatSearch DSS Park Press Select a or B as appropriateRD-9901 Remote Control Wall Plate Installation RD-9901 Remote Control Wall Plate Telephone CordPositioner Rear Panel Connect to ignition +12 VDC RD-9911 Warning Device Installation/OperationRCA cable Install two AA batteries provided Connect to vehicle groundCable Roof-thru Plate Installation QTYDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents DSS Uplink Signal Programming Uplink Control CentersIntroduction / HOW does Digital Satellite TV WORK? For Programming information call Dish NetworkPress Select a Finding the Satellite Method Using the City MenuSystem Operation Finding the Satellites Select a City Enter ElevationEntry of the previous state Start Search QuitCalculating Press Left arrow button to scroll list to the lastSearching Level = Setting DetectorFine Tuning Azimuth Moving to StartPress Select a if correct satellite was found Fine Tuning ElevationSystem has found a satellite and is fine tuning the signal Correct Satellite Continue SearchPress Select B Enter elevation, Figure Finding the Satellite Method Entering the ElevationPress Select B if correct satellite was not found El Angle =Press Select B Enter Location, Figure Enter Elevation Enter LocationPress Select B Press UP arrow buttonTo decrease latitude by 1o Latitude =Longitude = Press Left arrow buttonLatitude and longitude Putting Antenna in Park Position Move to Last Sat Manual Move Move to Last SatelliteManual Movement Manual Move EditAz3 = El 3 = XXX Press Select a to enter code Edit MenuEdit Search DSS Enter CodeEdit Select Search SatelliteSelect Search Sat Set Motor Positions 101.0Add/Edit Search Satellite Inactive EditQuit Press Select a to enter new satellite as search satellite Winegard* 165.0 QuitWinegard* 165.0 Edit Press Select a to enter satellite into memoryPage Satellite Remote Panel OperationSearch For Satellite Search routine againParking the Antenna Page Pinnacle Positioner Switch was removed 2/16/98 Positioner Controls & IndicatorsProgrammed City Locations Environmental Conditions PowerWinegard Important Safeguards Introduction No Satellite Found Antenna Reflector at Look angleLnbf Coax Center Conductor Return To Defaults Press Select a Set to Defaults. See Figure Test Functions Return to DefaultsSet to Defaults Quit Memory Restored Press Any KeyPositioner Does Not Respond Search Xxxxxx ParkPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Press Select a Test Remote Panel Test LNB Test Remote PanelTest Remote Panel Elevation = Press Select B Test Remote PanelThree times Test Remote Panel Search LED = OnTest Remote Panel Search LED = Off Press UP arrow button twicePress Right arrow button twice Test Remote Panel Park LED = OnTest Remote Panel Park LED = Off Test Remote Panel Search Key PressedTest Remote Panel Park Key Pressed Test LNB Min. is Signal level, max. isAntenna = 0 dB Level = Press Select a Test LNBPositioner Does Not Come On Make sure switch is all Way left or right dependingParking System, Fail Please Check Parking System Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Index Part Description QTY Number Antenna Support AssemblyMount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher
Top Page Image Contents