Winegard RD-9946 Park Move to Last Sat, Search DSS Park, Press Select a or B as appropriate

Page 13

2.Press SELECT A or B as appropriate

NOTE: All commands will be shown in bold with brackets, example [SELECT A].

11.Plug positioner into AC receptacle.

12.Press [UP/DOWN] arrow until you get Park displayed on positioner display. See Figure 14.

1.Press UP/DOWN arrow buttons to get Park on screen

SELECT A

SELECT B

PINNACLE POSITIONER

by WINEGARD

Park

Move to Last Sat

Model RD-9900

Figure 14

13.Press [SELECT A or B] Park to put antenna into park (travel) position. See Figure 14. The positioner will display Collapsing System while antenna is moving to travel position.

14.Verify that antenna is in the travel position (see Figures 2 and 3) when Collapsing System is replaced with normal menu, Figure 15.

SELECT A

SELECT B

PINNACLE POSITIONER

by WINEGARD

Search DSS Park

Model RD-9900

Figure 15

You are now ready to enjoy satellite TV! Refer to Operation Manual on how to acquire the satellite signal.

Rev. 6/98

13

Image 13

Contents Winegard Not applicable to mount and antenna Important SafeguardsUnpacking/Inventory Table Of ContentsInstallation Requirements Rev 9/98 Satellite System, RD-9946 proceed to step InstallationDo not Caulk Mount Base Ring Page Rev /99 Rev /98 Silver Device Refer to , Page 14 for operation and installationOptional RD-9911 Warning Connecttoignition+12VDCSensar TV Antenna Receiver To Receiver Control Wires To AntennaCH 3/4 OUT PositionerSearch DSS Park Park Move to Last SatPress Select a or B as appropriate Press UP/DOWN arrow buttons to get Park on screenRD-9901 Remote Control Wall Plate Telephone Cord RD-9901 Remote Control Wall Plate InstallationPositioner Rear Panel RCA cable Install two AA batteries provided RD-9911 Warning Device Installation/OperationConnect to vehicle ground Connect to ignition +12 VDCQTY Cable Roof-thru Plate InstallationDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents Introduction / HOW does Digital Satellite TV WORK? Uplink Signal Programming Uplink Control CentersFor Programming information call Dish Network DSSSystem Operation Finding the Satellites Finding the Satellite Method Using the City MenuSelect a City Enter Elevation Press Select aCalculating Start Search QuitPress Left arrow button to scroll list to the last Entry of the previous stateFine Tuning Azimuth Setting DetectorMoving to Start Searching Level =System has found a satellite and is fine tuning the signal Fine Tuning ElevationCorrect Satellite Continue Search Press Select a if correct satellite was foundPress Select B Enter elevation, Figure Finding the Satellite Method Entering the ElevationPress Select B if correct satellite was not found El Angle =Press Select B Enter Elevation Enter LocationPress UP arrow button Press Select B Enter Location, FigureLongitude = Latitude =Press Left arrow button To decrease latitude by 1oLatitude and longitude Putting Antenna in Park Position Move to Last Sat Manual Move Move to Last SatelliteManual Move Edit Manual MovementAz3 = El 3 = XXX Edit Search DSS Edit MenuEnter Code Press Select a to enter codeSelect Search Sat Set Motor Positions Select Search Satellite101.0 EditInactive Edit Add/Edit Search SatelliteQuit Winegard* 165.0 Edit Winegard* 165.0 QuitPress Select a to enter satellite into memory Press Select a to enter new satellite as search satellitePage Search For Satellite Remote Panel OperationSearch routine again SatelliteParking the Antenna Page Pinnacle Positioner Switch was removed 2/16/98 Positioner Controls & IndicatorsProgrammed City Locations Environmental Conditions PowerWinegard Important Safeguards Introduction Antenna Reflector at Look angle No Satellite FoundLnbf Coax Center Conductor Return To Defaults Set to Defaults Quit Test Functions Return to DefaultsMemory Restored Press Any Key Press Select a Set to Defaults. See FigureSearch Xxxxxx Park Positioner Does Not RespondPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Test Remote Panel Elevation = Test LNB Test Remote PanelPress Select B Test Remote Panel Press Select a Test Remote PanelTest Remote Panel Search LED = Off Test Remote Panel Search LED = OnPress UP arrow button twice Three timesTest Remote Panel Park LED = Off Test Remote Panel Park LED = OnTest Remote Panel Search Key Pressed Press Right arrow button twiceTest Remote Panel Park Key Pressed Test LNB Antenna = 0 dB Level = Signal level, max. isPress Select a Test LNB Min. isPositioner Does Not Come On Make sure switch is all Way left or right dependingParking System Fail Please Check Parking System, Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Index Part Description QTY Number Antenna Support AssemblyMount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher