Winegard installation manual Installation, Satellite System, RD-9946 proceed to step

Page 6

Installation

NOTE: If your RV/coach has been prewired for the Winegard Pinnacle RV

Satellite System, RD-9946 proceed to step 2.

1.Your RV/coach design (i.e. flat roof, rounded roof, obstructions, etc.) will determine how and where you mount the system. You have two options for running the control cable; Option A: Run the cable straight down from the mount (see Figure 5) or Option B (see page 15, cable roof-thru plate installation): Snap the knockouts on the base and run the cable to a different entry point (refrigerator vent, etc.)*. Figure 6 shows the knock out location on the base..

2.After determining how you want to run the control cable, you are ready to attach the mount base to the roof. Make sure the location you choose has adequate clearances; review Figures 1, 2 and 3. Figure 4 shows bolt hole pattern.

3.Attach mount base to roof (DO NOT BEND MOUNT BASE!). Remember to caulk all mounting holes and cable entry, see Figure 7. If running cable out through knockouts secure cable against whipping.

4.Make cable connections from 35' cable to mount assembly. Use FS-8100 to make coax connection. Use electrical tape to seal connections (Scotch® 33+ or 88 electrical tape is recommended). See Figure 7.

Rev 6/98

6

Image 6

Contents Winegard Important Safeguards Not applicable to mount and antennaTable Of Contents Unpacking/InventoryInstallation Requirements Rev 9/98 Installation Satellite System, RD-9946 proceed to stepDo not Caulk Mount Base Ring Page Rev /99 Rev /98 Optional RD-9911 Warning Device Refer to , Page 14 for operation and installationSilver Connecttoignition+12VDCCH 3/4 OUT To Receiver Control Wires To AntennaSensar TV Antenna Receiver PositionerPress Select a or B as appropriate Park Move to Last SatSearch DSS Park Press UP/DOWN arrow buttons to get Park on screenRD-9901 Remote Control Wall Plate Installation RD-9901 Remote Control Wall Plate Telephone CordPositioner Rear Panel Connect to vehicle ground RD-9911 Warning Device Installation/OperationRCA cable Install two AA batteries provided Connect to ignition +12 VDCCable Roof-thru Plate Installation QTYDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents For Programming information call Dish Network Uplink Signal Programming Uplink Control CentersIntroduction / HOW does Digital Satellite TV WORK? DSSSelect a City Enter Elevation Finding the Satellite Method Using the City MenuSystem Operation Finding the Satellites Press Select aPress Left arrow button to scroll list to the last Start Search QuitCalculating Entry of the previous stateMoving to Start Setting DetectorFine Tuning Azimuth Searching Level =Correct Satellite Continue Search Fine Tuning ElevationSystem has found a satellite and is fine tuning the signal Press Select a if correct satellite was foundFinding the Satellite Method Entering the Elevation Press Select B Enter elevation, FigureEl Angle = Press Select B if correct satellite was not foundPress UP arrow button Enter Elevation Enter LocationPress Select B Press Select B Enter Location, FigurePress Left arrow button Latitude =Longitude = To decrease latitude by 1oLatitude and longitude Putting Antenna in Park Position Move to Last Satellite Move to Last Sat Manual MoveManual Movement Manual Move EditAz3 = El 3 = XXX Enter Code Edit MenuEdit Search DSS Press Select a to enter code101.0 Select Search SatelliteSelect Search Sat Set Motor Positions EditAdd/Edit Search Satellite Inactive EditQuit Press Select a to enter satellite into memory Winegard* 165.0 QuitWinegard* 165.0 Edit Press Select a to enter new satellite as search satellitePage Search routine again Remote Panel OperationSearch For Satellite SatelliteParking the Antenna Page Pinnacle Positioner Positioner Controls & Indicators Switch was removed 2/16/98Programmed City Locations Power Environmental ConditionsWinegard Important Safeguards Introduction No Satellite Found Antenna Reflector at Look angleLnbf Coax Center Conductor Return To Defaults Memory Restored Press Any Key Test Functions Return to DefaultsSet to Defaults Quit Press Select a Set to Defaults. See FigurePositioner Does Not Respond Search Xxxxxx ParkPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Press Select B Test Remote Panel Test LNB Test Remote PanelTest Remote Panel Elevation = Press Select a Test Remote PanelPress UP arrow button twice Test Remote Panel Search LED = OnTest Remote Panel Search LED = Off Three timesTest Remote Panel Search Key Pressed Test Remote Panel Park LED = OnTest Remote Panel Park LED = Off Press Right arrow button twiceTest Remote Panel Park Key Pressed Test LNB Press Select a Test LNB Signal level, max. isAntenna = 0 dB Level = Min. isMake sure switch is all Way left or right depending Positioner Does Not Come OnParking System, Fail Please Check Parking System Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Antenna Support Assembly Index Part Description QTY NumberMount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher