Texas Instruments TLV1562 manual Software Overview, elseif NOINT0SIG

Page 57

.elseif NO_INT0_SIG

Software Overview

.elseif NO_INT0_SIG

*instead of using the INT signal, the processor waits

*for 6ADCSYSCLK+49ns and reads then the sample repeat(#32)

nop		; wait for 34 processor cycles
.endif
* read sample
STEP7: @ADSAMPLE = port(ADC)		; read the new sample into the DSP

XF	= 1	; set RD

.if (SEND_OUT_PARALLEL)

* store sample into the parallel buffer location if choosen

port(DAC1) = @ADSAMPLE	; update DAC output

@TEMP = port(ADC)	; activate ADC CS again
.endif

.if (AUTO_PWDN)

*deselect/select the ADC with CS (requirment in Auto power down mode) @TEMP = port(DEACTIVE) ; deselect ADC

@TEMP = port(ADC)	; activate ADC CS again
repeat(#18)
nop	; wait for 20 clock cycles [t(APDR)=500ns]

.endif

XF	= 0	; clear RD (step 4)
call	STORE	; handle storing of the samples into memory and serail DAC
.if INT0_DRIVEN
return		; return from routine back to IRQ_INT0
.else
goto	STEP5	; go back to receive next sample
.endif

**********************************

*STORE:

*saving the samples into memory

**********************************

STORE:

.if SAVE_INTO_MEMORY

* store new sample into DSP data memory

*AR7+ = data(@ADSAMPLE) ; write last sample into memory table

.endif

.if SEND_OUT_SERIAL

* store sample into the serial buffer location

Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP

51

Image 57

Contents SLAA040 JulyApplication Report TParalInteMS3rflelADConvertertotheacing20C54xDSPtheTLV1562IMPORTANT NOTICE Contents 8.5.5 List of Figures List of TablesFigures viSLAA040 1 Introduction Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP2 The Board 2.1 TMS320C54x Starter Kit2.3 ADC TLV1562 Overview 2.2 TLV1562EVM2.3.1 Suggestions for the ’C54x to TLV1562 Interface 2.3.1.1 The Universal InterfaceUsing RD or the CSTART Signal to Start Conversion 2.3.2 Recyclic ArchitectureFigure 2. TLV1562 to ’C54x DSP Interface of the EVM 2.3.3 Note on the Interface, Using an External ADC Clock Drive 2.4 Onboard Components2.4.1 TLC5618A - Serial DAC 2.4.2 THS5651 - Parallel Output CommsDAC Figure 3. TLC5618A to ’C542 DSP InterfaceFigure 4. THS5651 to C542 DSP Interface 3 Operational Overview 3.1 Reference Voltage Inputs3.2 Input Data Bits 3.3 Connections Between the DSP and the EVM Table 1. Signal ConnectionsTable 2. 3-Position Jumpers 3.3.1 Jumpers Used on the TLV1562EVMTable 3. 2-Position Jumpers 8SLAA040Table 4. DSP/DAC Interconnection 4 The Serial DAC/DSP System5 The DSP Serial Port Table 5. DSP Serial Port Signals and Registers6.1 DSP Internal Serial Port Operation 6 Other DSP/TLV1562 Signals7 Conversation Between the TLV1562 and the DSP 7.2 Mono Interrupt Driven Mode Using RD7.1 Writing to the ADC Table 6. DSP Algorithm for Writing to the ADCTable 7. DSP Algorithm for Mono Interrupt Driven Mode Using RD tDCSL-sample+1ADCSYSCLKtENDATAOUT = 41 ns 7.3 Mono Interrupt Driven Mode Using CSTART Table 8. DSP Algorithm for Mono Interrupt Driven Mode Using CSTART14 SLAA040 Table 9. DSP Algorithm for Dual Interrupt Driven Mode 7.4 Dual Interrupt Driven Mode7.5 Mono Continuous Mode Table 10. DSP Algorithm for Mono Continuous Mode16 SLAA040 Table 11. DSP Algorithm for Dual Continuous Mode 7.6 Dual Continuous Mode8 Software Overview 8.1 Software Development tools8.2 DSP Memory Map Figure 5. Memory Map 8.3 Programming Strategies for the ’C54x, Explanations 8.3.3 Timer Output8.3.1 Optimizing CPU Resources for Maximum Data Rates 8.3.2 Address and Data Bus for I/O Tasks8.3.5 Generating the Chip Select Signal and the CSTART Signal 8.3.4 Data Page Pointer8.3.6 Interfacing the Serial DAC 5618A to the DSP 8.3.8 Branch Optimization goto/dgoto, call/dcall 8.3.7 Interrupt LatencyGOTO MARK MARK DP = #1 ARP = #58.3.9 Enabling Software Modules .if/.elseif/.endif 8.4 Software Code Explanation8.4.1 Software Principals of the Interface 8.4.1.1 Software Polling 8.4.1.2 Timed SolutionAdvantage Disadvantage8.4.1.5 Setting the Right Switches 8.4.1.3 Interrupt Driven SolutionAdvantages DisadvantagesTable 12. Switch Settings TaskTable 13. Instruction in the Program Header Step 8.5.1 The Mono Interrupt Driven Mode Using RD to Start Conversion 8.5 Flow Charts and Comments for All Software ModesTable 14. Instruction in the Program Header Step 8.4.1.6 Common Software for all ModesOther Files Program FilesCode verification common file of all modes constants definitionFigure 6. Software Flow of the Mono Interrupt Driven Solution Calibration procedure of the DAC 8.5.2 Mono Interrupt Driven Mode Using CSTART to Start ConversionIncludes the complete software algorithm to control the monomode Common file of all modes constants definitionSAVE Initialize SPIPoll INTO Pin Until h/0 Transition Occurs Pull Down CSTARTThis only works for one TLV1562 not multiple because CS is not used 8.5.2.1 Throughput Optimization†8.5.3 Dual Interrupt Driven Mode Figure 8. Time Optimization monocst1Maximum Performance at 1.2 MSPS with Internal Clock IMPORTANT NOTE The code has been optimized to maximize the data throughput. It was found that CSTART can be pulled low earlier than the data read instruction is performed by the DSP. This saves the 100-ns wait time in STEP 3 because the data read requires at least 100 ns. Therefore, CSTART gets pulled high directly after data read, and the interface becomes faster and gains throughput. This variation will be found in the code. The data acquisition is done in a small number of steps that explains everything inside the code Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP 8.5.4 Mono Continuous Mode Figure 10. Flow Chart Mono Continuous Mode 8.5.5 Dual Continuous Mode Figure 11. Flow Chart Dual Continuous Mode Program Files 8.6 Source Code 8.6.1 Common Software for all Modes except C-Callable8.6.1.1 Constants.asm 42 SLAA040 set 000C0h Operate without calibrated inputs no offset8.6.1.2 Interrupt Vectors 44 SLAA040 4C internal timer interrupt8.6.1.4 Auto.bat 8.6.1.3 linker,cmdFile Linker.lnk COMMAND FILE title ”COMMAND FILE FOR TLV1562.ASM”pointer address when using any of the following variables Mainprogram Monomode.asmjump address to init. new channel counter for one channelsent value to register CR0 of the ADC if SENDOUTSERIAL endif if INT0DRIVENPOLLINGDRV48 SLAA040 endif endif if DIFFINPUTMODE if AUTOPWDNENABLE= bit*AR5,15-0 elseif INT0DRIVENelseif NOINT0SIG 52 SLAA040 CALIBRAT.ASM 8.6.3 Calibration of the ADC54 SLAA040 if SMECALIBRATION 56 SLAA040 endif 58 SLAA040 Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP 60 SLAA040 if INT0DRIVENPOLLINGDRV 62 SLAA040 = bit*AR5,15-0 64 SLAA040 endif if SAVEINTOMEMORYSoftware Overview Constants definition - see 8.6.1.1 Constants.asm 8.6.5 Dual Interrupt Driven ModeInterrupt Routine handler - see 8.6.1.2 Interrupt Vectors Mainprogram DUALIRQ1.asmInterfacing the TLV1562 Parallel ADC to the TMS320C54x DSP Software Overviewif SENDOUTSERIAL Software OverviewSoftware Overview 70 SLAA040 Software Overview 72 SLAA040 endif 8.6.6 Mono Continuous Mode Mainprogram MONOCON1.asm74 SLAA040 Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP 76 SLAA040 endif if EXTERNALCLOCK 78 SLAA040 endif if SAVEINTOMEMORY 8.6.7 Dual Continuous Mode Mainprogram DUALCON1.asm80 SLAA040 Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP 82 SLAA040 endif if EXTERNALCLOCK 84 SLAA040 Interfacing the TLV1562 Parallel ADC to the TMS320C54x DSP Mainprogram C1562.c 8.6.8 C-CallableTLV1562Channel, Save Memory Start address, NUMBEROFSAMPLES 80h samples of channel 1 will be stored beginning on 2000hInterfacing the TLV1562 Parallel ADC to the TMS320C54x DSP 88 SLAA040 AR7+ = data@ADSAMPLE 90 SLAA040 Vectors.asmint2 returnenable 48 external interrupt int2 nop Auto.bat Linker.cmd92 SLAA040 10 References 9 Summary