Memorex MVR041, MVR2040A, MVR2041 Special Playback, Using Zero Return, Recording a TV Program

Page 18

SPECIAL PLAYBACK

TO VISUALLY SEARCH FOR

DESIRED POINTS

When either the F.FWD or REW button is pressed in the PLAYBACK mode, the speed search picture will appear. The CUE indicator or the REV indicator will light in the display for about 4 seconds. When pressed twice, the search picture will increase speed. Speed search time depends upon the speed used (SP, LP or SLP) during recording.

TO WATCH A STILL PICTURE

Press the PAUSE/STILL button in the PLAYBACK mode. The PLAY indicator will flash in the display for about 4 seconds. Press the PAUSE/STILL button again to resume normal playback.

FRAME BY FRAME ADVANCE

Press the SLOW button during STILL playback. The still picture will advance by one frame each time you press the button. Hold the button for continuous frame by frame viewing.

Press the PAUSE/STILL button again to resume normal playback.

NOTES: • A few noise bars will appear on the picture during SPEED SEARCH and STILL.

The audio output is muted during SPEED SEARCH, STILL, FRAME ADVANCE and

SLOW MOTION.

To prevent damage to the tape, special playback is automatically changed to the PLAYBACK mode after 5 minutes.

SLOW MOTION PLAYBACK

Press the SLOW button in the PLAYBACK mode. Playback will proceed at 1/10th of the normal speed. The SLOW indicator will light in the display for about 4 seconds. Press the PLAY button again to resume normal playback.

NOTE: SLOW TRACKING AND VERTICAL LOCK ADJUSTMENT

If noise bars appear in the picture during slow motion, press the TRACKING/SET + or – button to reduce the noise bars.

If the still picture jitters excessively, press the TRACKING/SET + or – button to stabilize the still picture.

TO WATCH A TAPE REPEATEDLY

CHECK BEFORE YOU BEGIN

Turn ON the TV and set to the video channel 3 or 4.

Turn ON the VCR POWER button.

Press the TV/VCR selector button to select the VCR mode.

When a TV is connected with an audio/video cable, turn the TV and this VCR on, and select the video input mode on the TV.

1 Press the MENU button.

 

MENU

 

 

CLOCK SET

 

Press the TRACKING/SET +

 

TIMER REC SET

 

 

 

 

 

 

 

 

or – button to select the AUTO

 

 

AUTO REPEAT ON

OFF

 

 

 

 

CH SET UP

 

REPEAT option.

 

 

 

LANGUAGE/IDIOMA/LANGUE

 

 

 

 

 

 

NO NOISE BACKGROUND

 

 

 

 

 

 

 

ON

OFF

+/–/ENTER/MENU

2 Press the ENTER button to

 

MENU

 

 

 

 

 

select the ON position.

 

CLOCK SET

 

 

TIMER REC SET

 

 

 

3 Press the MENU button.

 

 

AUTO REPEAT ON

OFF

 

 

 

 

CH SET UP

 

 

 

LANGUAGE/IDIOMA/LANGUE

 

 

If you press the PLAY button, the

 

 

NO NOISE BACKGROUND

 

 

 

tape will play over and over until

 

ON

OFF

+/–/ENTER/MENU

 

the repeat mode is canceled.

" " will appear if you press the CALL button. To cancel, press the CALL button again.

NOTE: To cancel repeat mode, follow the above steps 1 and 2, then press the ENTER button to select the OFF position. Press the MENU button to return to the TV.

USING ZERO RETURN

The zero return function provides a convenient method of rapidly returning to the starting point of recording or playback. The starting point can be indexed for any location on the tape by pressing the COUNTER RESET button and ZERO RETURN button.

1Press the CALL button to display the counter on the screen. (When loading a cassette tape, the clock will change to the counter automatically in the display.)

2Before playback or recording, press the COUNTER RESET button to set the counter to "00:00:00".

3Begin playback or recording.

4Press the STOP button when playback or recording is finished.

5Press the ZERO RETURN button. The tape will rewind and automatically stop at the "00:00:00" position.

RECORDING A TV

PROGRAM

RECORDING AND VIEWING THE SAME TV PROGRAM

CHECK BEFORE YOU BEGIN

Turn ON the TV and set to the video channel 3 or 4.

Turn ON the VCR POWER button.

Press the TV/VCR selector button to select the VCR mode.

When a TV is connected with an audio/video cable, turn the TV and this VCR on and select the video input mode on the TV.

1Load a cassette tape with the erase prevention tab intact. The VCR will automatically

turn on. The clock display will change in the counter display.

2 Press the SPEED selector button to select the desired tape speed SP or SLP.

The counter and SP or SLP will appear on the screen for

18

about 4 seconds.

00 : 00 : 00 SP

4E30401A E P14-19

18

17/04/2001, 14:01

Image 18
Contents MVR2040A Series C MVR2041 Read Instructions CleaningAccessories Retain InstructionsVentilation Power SourcesPower Lines Grounding or PolarizationSafety Check Damage Requiring ServiceReplacement Parts HeatMoisture Condensation PrecautionsPower Source Location and HandleBattery Installation Precautions FeaturesBattery Cautions Effective Distance of the Remote ControlTable of Contents Remote Control Location of ControlsFront Rear Fluorescent Display2829 Basic Connections Antenna to VCR ConnectionSeparate VHF and UHF Antennas VCR to TV Connection Catv Cable TV Connections Cable Descrambler SwitchIncoming Converter Allows PreventsAUDIO/VIDEO Connections AUDIO/VIDEO ConnectionStereo Amplifier Connections Language Selection Setting the Video ChannelSetting the Clock Check Before YOU BeginNoise Elimination Setting the ChannelsAutomatic Memory Tuning To ADD/DELETE ChannelsPlayback Using Zero Return Special PlaybackRecording a TV Program To Prevent AN Accidental Recording Recording ONE Program While Watching AnotherTo Stop Recording To Record AgainONE-TOUCH Timer Recording OTR Setting the Timer RecordingIntact. The VCR will automatically turn on ON-SCREEN Function Display Make all connections before turning on the power Video Head CleaningVideo Head Cleaning Duplicating a Video TapeTV Broadcast Reception Before Requesting ServiceSymptom Cause Possible Solution Power RecordingSpecifications Symptom Cause Possible Solution Remote ControlMemo Precaucion Tormentas Electricas VentilacionFuentes DE Alimentacion Lineas DE AlimentacionPiezas DE Repuesto Servicio19. DAÑ OS QUE Requieran Reparacion Revision DE SeguridadPosicion Y Manejo PrecaucionesCondensacion DE Humedad Fuente DE AlimentacionCaracteristicas Precaucion CON LAS PilasInstalacion DE Pilas Presentació n de 3 idiomas en pantalla Usted IndiceSistema automá tico de repetició n de reproducció n Visualizador fluorescente de funció n mú ltiple EnUbicacion DE LOS Controles Parte DelanteraControl Remoto Parte Trasera Visualizador FluorescenteConexiones Basicos Conexion DE Antena a VideograbadorConexion DEL Videograbador a UN Televisor Televisor con entrada única de 75 ohmios para VHF/UHFConexiones DE TV Cable Catv Permite No PermiteInterruptor DivisorInterruptor A/B Conexiones DE AUDIO/VIDEO Conexion DE AUDIO/VIDEOConexion DEL Amplificacor Estereo Seleccion DE Idioma Ajuste DEL Canal DE VideoAjuste DEL Reloj Para un sintonizador de TV de pulsadorBorrado DE UN Canal DE LA Memoria Ajuste DE CanalesEliminacion DE Ruido Seleccion DE TV/CATVColocacion Y Extraccion ReproduccionReproduccion Especial USO DE Retorno AL CeroGrabacion DE UN Programa DE TV Para Grabar UN Programa Mientras SE VE Otro Para Detener LA GrabacionPara Detener Temporalmente LA Grabacion VHF/UHF/CATV CanalsAjuste DE LA Grabacion POR Temporizador Confirme Antes DE EmpezarEncienda el TV y fije el Canal 3 ó Indicacion DE Funciones EN LA Pantalla Duplicacion DE UNA Cinta DE Video Limpieza DE LA Cabeza DE VideoPresione el botón de Input Antes DE Solicitar Servicio Control Remoto