Marantz RC3001 manual Sys.Setup, Clock Clock Setting

Page 25

ENGLISH

	3. SYS.SETUP		2. Use the numeric buttons (0 to 9) and cursor
	Display the MAIN MENU on the LCD of the		buttons (t and u) to set the current time.
	Display the MAIN MENU on the LCD of the		After setting the correct time, press the
	RC3001, then press the button next to the “SYS.		After setting the correct time, press the
	RC3001, then press the button next to the “SYS.		ENTER button.
	SETUP” indicator.		ENTER button.
	SETUP” indicator.
	The items below can be set in the SYS.SETUP
	The items below can be set in the SYS.SETUP
	screen.

• CLOCK (Clock setting)

• BACK LIGHT (Backlight illumination time setting)

• LCD (LCD setting)

• BEEP (Beep sound setting)

• MEM CLEAR (Initialization setting)

3. The message “COMPLETED” is displayed in the LCD to indicate that the clock setting is completed.

CLOCK (CLOCK SETTING)

This sets the clock for the RC3001.

1. Press the button next to the “CLOCK” indicator in the SYS.SETUP menu screen in the LCD to display the clock setting screen.

•Either press the ENTER button or wait three seconds for the LCD to automatically return to the SYS.SETUP menu.

•Pressing the Home button returns the LCD to the MAIN MENU.

Notes:

The clock can become out of sync over time. Please check it occasionally and set to the correct time if necessary.

The clock setting is not backed up when the battery pack is replaced. Please reset the time after replacing the battery pack.

20

Image 25

Contents Model RC3001 User Guide For US and Canada Español EnglishFrançais DeutschFrançais EnglishDeutsch EspañolRECYCLING-HINWEIS Remarque Concernant LE RecyclageNota Sobre EL Reciclado Nota SUL RiciclaggioFeatures Table of ContentsPack Into the Remote Controller Load the Rechargeable BatteryAttach the battery case cover Before USERemove the bottom cover of the remote Charging the Battery PackController, and connect the AC adapter To the charging terminal next to the USB portCommand Remote ControllerRemote controller display Home mode and the device modesRemote Controller LCD This jack connects to the supplied AC adapter This is a rod antenna for receiving RF signalsThis jack connects the supplied IR emitter cable Mounting Location Precautions InstallationMounting Procedure Precautions Mounting Procedure5mm Using the Remote Controller Using the Remote Controller With Infrared RaysChanging the IR / RF Settings With Radio FrequencyConnecting to Marantz Equipment Connecting the RX3001 with Other DevicesConnecting to AN AC Adapter Connecting to NON-MARANTZ EquipmentConnect the supplied AC adapter to the DC jack Setting the IR Output Level SetupSetting the Channel Output 4+5+6 Output 1+2+3Emitter Output Output signal Setting the Group ID SelectorSleep Timer RC3001 Button SettingsDVD input command for Marantz AV Receiver Basic OperationMain Menu Other OperationLearning Function Entering the Main MenuPress the button next to the displayed This screen changes to Home modeTo learn Checking the Settings TimerOperation Settings Press the button next to the Timer SETPress a button next to the Everyday or Either press the Enter button or wait Operation ON/OFF SettingsClock Clock Setting SYS.SETUPBacklightbacklightillumination Time Setting LCD Timer LCD timer setting LCD LCD SettingMessage Completed is displayed This sets the built-in beep sound in the RC3001 Beep Beep Sound SettingMEM Clear Initialization Setting Reset Status IndicatorProgrammable Codes Specifications 90g 0.2lbs Up to 100kHzDC9V 800mA MIN105mm 4-3/16insOthers Cleaning of Equipment External SurfacesRepairs If the equipment becomes heavily soiledIs a registered trademark