Marantz RC3001 manual Before USE, Load the Rechargeable Battery, Pack Into the Remote Controller

Page 7

ENGLISH

BEFORE USE

 

LOAD THE RECHARGEABLE BATTERY

 

 

PACK INTO THE REMOTE CONTROLLER

 

1. Remove the battery case cover.

 

Battery case cover

2. Insert the rechargeable battery cable connector into the socket of the remote controller.

Rechargeable battery pack

3. Pull the cable of the rechargeable battery pack around so that it does not get caught in the case as shown in the figure below, then load the rechargeable battery pack into the battery case.

Cable

4. Attach the battery case cover.

Battery case cover

•When removing the battery pack, take off the battery case cover, then pull up the ribbon stretched at the bottom of the battery case to take out the rechargeable battery pack from the battery case.

CAUTION ON BATTERY

•Be sure to use only the rechargeable nickel metal-hydride (Ni-MH) battery pack that is supplied with the remote controller.

•When loading, be sure to properly attach the rechargeable battery cable connector to the remote controller socket.

•Be sure to properly dispose of the rechargeable battery pack in accordance with the guidelines (regulations) for your local area.

REPLACING THE BATTERIES

The batteries in the Remote controller are Nickel Metal Hydride (Ni-MH) batteries. It is advised to change the batteries when the operation of the Remote controller becomes unreliable.

If you want to order new batteries, please contact your Marantz authorized dealer or Marantz customer service.

Warning:

Replace the batteries only with original Marantz RC3001 batteries; otherwise the guarantee is no longer valid and hazardous situations could occur.

2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model RC3001 User Guide For US and Canada Deutsch EnglishEspañol FrançaisEspañol EnglishFrançais DeutschNota SUL Riciclaggio Remarque Concernant LE RecyclageRECYCLING-HINWEIS Nota Sobre EL RecicladoFeatures Table of ContentsBefore USE Load the Rechargeable BatteryPack Into the Remote Controller Attach the battery case coverTo the charging terminal next to the USB port Charging the Battery PackRemove the bottom cover of the remote Controller, and connect the AC adapterHome mode and the device modes Remote ControllerCommand Remote controller displayRemote Controller LCD This jack connects to the supplied AC adapter This is a rod antenna for receiving RF signalsThis jack connects the supplied IR emitter cable Mounting Procedure InstallationMounting Location Precautions Mounting Procedure Precautions5mm With Radio Frequency Using the Remote Controller With Infrared RaysUsing the Remote Controller Changing the IR / RF SettingsConnecting to Marantz Equipment Connecting the RX3001 with Other DevicesConnecting to AN AC Adapter Connecting to NON-MARANTZ EquipmentConnect the supplied AC adapter to the DC jack Output 4+5+6 Output 1+2+3 SetupSetting the IR Output Level Setting the ChannelEmitter Output Output signal Setting the Group ID SelectorBasic Operation RC3001 Button SettingsSleep Timer DVD input command for Marantz AV ReceiverEntering the Main Menu Other OperationMain Menu Learning FunctionPress the button next to the displayed This screen changes to Home modeTo learn Press the button next to the Timer SET TimerChecking the Settings Operation SettingsPress a button next to the Everyday or Either press the Enter button or wait Operation ON/OFF SettingsClock Clock Setting SYS.SETUPBacklightbacklightillumination Time Setting LCD Timer LCD timer setting LCD LCD SettingMessage Completed is displayed This sets the built-in beep sound in the RC3001 Beep Beep Sound SettingMEM Clear Initialization Setting Reset Status IndicatorProgrammable Codes Specifications MIN105mm 4-3/16ins Up to 100kHz90g 0.2lbs DC9V 800mAIf the equipment becomes heavily soiled Cleaning of Equipment External SurfacesOthers RepairsIs a registered trademark
Top Page Image Contents