Panasonic AJ-D230HP operating instructions Video Head Cleaning, Condensation, Maintenance

Page 37

Video Head Cleaning

This VTR comes with an auto head cleaning function which automatically reduces the amount of dirt on the heads. However, to ensure the highest reliability, we recommend that you clean the video heads every day.

Use the cleaning fluid designated by Panasonic.

Checking the hour meter

1

Set the VTR to the remote mode.

 

(Set the LOCAL/MENU/REMOTE switch to the REMOTE position.)

2

When the RESET button on the front panel is pressed, the cumulative numbers of

 

hours during which the drum and capstan have been used are indicated alternately

on the counter display for as long as the button is held down.

Cumulative drum rotation time

Cumulative capstan rotation time

Condensation

The principle according to which condensation forms is the same as that which causes droplets of water (condensation) to form on the window panes of a heated room when it is cold outside. Condensation forms on the VTR or its tape when it is moved to a location with a considerably different temperature and humidity. More specifically, it forms when the VTR or tape is:

Brought into a very steamy and humid location or into a room where the heating was just turned on.

Brought suddenly from an air-conditioned room to a very hot and humid location.

In such cases, do not turn the power on straight away but leave the unit standing for about 10 minutes. When condensation has formed in the unit, an error message lights up in the counter display section, and the cassette tape is automatically ejected.

Keep the power on and wait until the error message is cleared.

Maintenance

Before performing any maintenance work, set the power switch to the OFF position and disconnect the power cable from the AC outlet making sure that you take hold of the molded part of the power plug.

Use a soft cloth to clean the cabinet. In order to get rid of stubborn dirt, dilute some neutral kitchen detergent with water, dip a cloth into the solution, wring it out well, and wipe away the dirt. Then wipe off any moisture which remains using a dry cloth.

Do not use paint thinners or benzine for cleaning purposes.

37

Image 37
Contents Operating Instructions FCC Note Table of Contents RS-232C Interface Introduction FeaturesFront Panel Controls and Their FunctionsCounter display area LOCAL/MENU/REMOTE switch Power switchInput Select switch Cassette slotVolume recording level control Volume controlRemote control connector Reset buttonConnector section Signal GND terminal AC in connectorHandle Video in connector Sync in connectorType TapesDescription Use of Panasonic consumer DV cassette tape is recommendedSwitch on the power Switching on the power and inserting the cassetteOperation Insert the cassette tapePrecautions for setting the still timer Stop modeRecording Playback Pause/still recording back-space assemble recordingCue and Review Still-picture playbackFrame advance Mode Audio OUT connectors Display tubeSound selection Use the Audio OUT Select button to select the desired soundRepeat playback Set the VTR to the menu modeMenu screen Setting Description of operation Set the VTR to the local modeOFF MEM Stop Repeat Continue Time code Time Code and User’s BitUser’s bit Setting the user’s bit Setting the time codeDisplay changes as shown below Time code and user’s bit playbackSuperimposed Display Screens Operating modeCharacters displayed Display positionChanging a setting Set-up Default SettingsSetting Upon completion of the setting, press the SET REC buttonSet-up Menus SettingBasic menu Operation menu Description of settingsInterface menu Type Format SEL settingTape Protect menu Memory Mode menuTime Code menu Setting Description of settingsColor Video menuMute LOW-RFAudio menu RS-232C InterfaceExample of wiring connections Interface specificationsPin No Signal Communication parametersSending format from personal computer to VTR Data format External interface specificationsReceiving format from VTR to personal computer Communication system Asynchronous, full duplex Baud rateSTX QOP ETX ACK STX OEJ ETX STX QCD ETX ACK STX CD Status command Command list Key commandsVTR operation mode Code Send Description of operationStandby OFF commands Counter sense commandDeck ID command Description of error Error NoMaintenance Video Head CleaningSet the VTR to the remote mode CondensationOutput connectors Input connectorsDigital video Line IN/line OUTService Centers