Panasonic AJ-D230HP operating instructions Set-up Menus, Basic menu, Setting

Page 24

Set-up Menus

BASIC menu

Item

No.	S u p e r i m p o s e d	No.
	d i s p l a y

000DISPLAY SEL 0000 0001 0002

001CHARA H-POS 0000 0001

0003

0007

002CHARA V-POS 0000

0001

0003

0007

003 CHARA TYPE 0000

0001

005MENU INHIBIT 0000 0001

Setting

S u p e r i m p o s e dDescription of settings

d i s p l a y

OFF This sets what is to be displayed for the superimpose TIME signals output from the MONITOR OUT connector.

T, STA 0: No display

1:Only the time is displayed.

2:The time and operation mode are displayed.

0This sets the horizontal position of the superimposed

1characters (8 settings to choose from).

:

3

:

7

0	This sets the vertical position of the superimposed
1 characters (8 settings to choose from).
:
3
:
7
WHITE	This selects the type of characters for the
W/OUT	superimposed display and menu display.
	0: White characters appear on a black back ground.
	1: White characters with black borders appear.
OFF	This selects whether or not the menu settings are to be
ON	fixed.
	0: The settings are not fixed.
	1: The settings are fixed (and cannot be changed).

The underlined number and item are the factory settings.

.<Notes>

While setting “CHARA H-POS”, “CHARA V-POS”, and “CHARA TYPE”, the counter display can be viewed by holding down the MODE button, allowing you to check the settings. You can also use the

.DATA+ and DATA– buttons while holding down the MODE button to adjust the values while you are viewing them.

To set ON or OFF for the “MENU INHIBIT” item, first press the DATA+ or DATA– button while holding down the MODE button, and then select the setting.

Continuously after performing the settings, press the SET button (REC button) to exit the menu. The MENU INHIBIT setting takes effect starting with the next menu mode.

24

Image 24

Contents Operating Instructions FCC Note Table of Contents RS-232C Interface Features IntroductionControls and Their Functions Front PanelCounter display area Power switch LOCAL/MENU/REMOTE switchInput Select switch Cassette slotVolume control Volume recording level controlRemote control connector Reset buttonConnector section AC in connector Signal GND terminalHandle Video in connector Sync in connectorTapes TypeDescription Use of Panasonic consumer DV cassette tape is recommendedSwitching on the power and inserting the cassette Switch on the powerOperation Insert the cassette tapeStop mode Precautions for setting the still timerRecording Pause/still recording back-space assemble recording PlaybackCue and Review Still-picture playbackMode Audio OUT connectors Display tube Frame advanceSound selection Use the Audio OUT Select button to select the desired soundSet the VTR to the menu mode Repeat playbackMenu screen Set the VTR to the local mode Setting Description of operationOFF MEM Stop Repeat Continue Time Code and User’s Bit Time codeUser’s bit Setting the time code Setting the user’s bitTime code and user’s bit playback Display changes as shown belowOperating mode Superimposed Display ScreensCharacters displayed Display positionSet-up Default Settings Changing a settingSetting Upon completion of the setting, press the SET REC buttonSetting Set-up MenusBasic menu Description of settings Operation menuType Format SEL setting Interface menuMemory Mode menu Tape Protect menuSetting Description of settings Time Code menuVideo menu ColorMute LOW-RFRS-232C Interface Audio menuInterface specifications Example of wiring connectionsPin No Signal Communication parametersExternal interface specifications Sending format from personal computer to VTR Data formatReceiving format from VTR to personal computer Communication system Asynchronous, full duplex Baud rateSTX QOP ETX ACK STX OEJ ETX STX QCD ETX ACK STX CD Command list Key commands Status commandVTR operation mode Code Send Description of operationCounter sense command Standby OFF commandsDeck ID command Error No Description of errorVideo Head Cleaning MaintenanceSet the VTR to the remote mode CondensationInput connectors Output connectorsDigital video Line IN/line OUTService Centers