Panasonic AJ-D230HP Digital video, Line IN/line OUT, Input connectors, Output connectors

Page 38

SPECIFICATIONS

GENERAL

Power

supply:

 

Power

consumption:

Ambient operating temperature:

Ambient operating humidity:

Weight:

Dimensions (W × H × D):

Recording format:

Recording tracks:

Time code:

Digital audio:

Cue track:

Control (CTL):

Tape speed:

Recording time:

Tape used:

FF/REW time:

120 V AC, 50Hz-60Hz

49W

41°F to 104°F (5°C to 40°C)

35% to 80%

15.4 Ibs. (7.0 kg)

8-7/16” × 5-1/4” × 15-7/16” (214 × 132 × 391 mm)

DVCPRO Digital video

Recorded in sub-code area

2channels

1 track

1track 33.820 mm/sec.

126 minutes (using AJ-P126LP tape)

66minutes (using AJ-P66MP tape) 1/4” thin magnetic layer metal tape Within 3.5 min. (using AJ-P126LP tape)

VIDEO

(Digital video)

Sampling frequency:

13.5 MHz for Y; 3.375 MHz for PB/PR

 

Quantizing:

8 bits

 

(Line IN/line OUT)

Error correction:

Reed-Solomon product code

 

Video band:

30 Hz to 4.5 MHz (–1±1 dB) for Y

 

Y/C delay:

Less than 20ns

 

(Input connectors)

K factor:

Less than 3%

 

Line input:

BNC × 1; 1.0 VP-P, 75

 

 

SYNC input:

BNC × 1; 1.0 VP-P, 75

 

 

S-VIDEO:

4P × 1; Y: 1.0 VP-P, 75

(burst level)

(Output connectors)

Line output:

C: 0.286 VP-P, 75

BNC × 1; 1.0 VP-P, 75

 

 

Monitor output:

BNC × 1; 1.0 VP-P, 75

 

 

S-VIDEO:

4P × 1; Y: 1.0 VP-P, 75

(burst level)

 

 

C: 0.286 VP-P, 75

AUDIO

(Digital audio)

Sampling frequency:

48 kHz

 

Quantizing:

16

bits

 

Frequency response:

20

Hz to 20 kHz ( :;I,”ii)

 

Dynamic range:

More than 85 dB (1 kHz, emphasis OFF, “A” weighted)

 

Distortion:

Less than 0.1% (1 kHz, emphasis OFF, reference level)

(Input connectors)

Crosstalk:

Less than –80 dB (1 kHz, between 2 channels)

Line input (CH1/CH2):

PHONO × 2; –8 dBV, 47 k

(Output connectors)

Line output (CH1/CH2):

PHONO × 2; –8 dBV, 1 k

 

Headphones output:

M3 stereo, variable level (max. –32 dBV or more), 8

OTHER INPUT/OUTPUT CONNECTORS

Display Tube

RS-232C:

D-SUB, 25P, RS-232C interface

Wired remote control:

M2 jack (simple remote control)

Counter:

8 digits (CTL/TC/UB selectable, remaining tape)

Audio level meter:

18 steps

Other:

REC/REC INH, REMOTE, WIDE, “Consumer-use cassette

 

loaded” display, REPEAT, SERVO, Channel condition,

 

“Cassette loaded” display

38

Image 38
Contents Operating Instructions FCC Note Table of Contents RS-232C Interface Features IntroductionCounter display area Controls and Their FunctionsFront Panel Input Select switch Power switchLOCAL/MENU/REMOTE switch Cassette slotRemote control connector Volume controlVolume recording level control Reset buttonConnector section Handle Video in connector AC in connectorSignal GND terminal Sync in connectorDescription TapesType Use of Panasonic consumer DV cassette tape is recommendedOperation Switching on the power and inserting the cassetteSwitch on the power Insert the cassette tapeStop mode Precautions for setting the still timerRecording Cue and Review Pause/still recording back-space assemble recordingPlayback Still-picture playbackSound selection Mode Audio OUT connectors Display tubeFrame advance Use the Audio OUT Select button to select the desired soundMenu screen Set the VTR to the menu modeRepeat playback OFF MEM Stop Repeat Continue Set the VTR to the local modeSetting Description of operation User’s bit Time Code and User’s BitTime code Setting the time code Setting the user’s bitTime code and user’s bit playback Display changes as shown belowCharacters displayed Operating modeSuperimposed Display Screens Display positionSetting Set-up Default SettingsChanging a setting Upon completion of the setting, press the SET REC buttonBasic menu SettingSet-up Menus Description of settings Operation menuType Format SEL setting Interface menuMemory Mode menu Tape Protect menuSetting Description of settings Time Code menuMute Video menuColor LOW-RFRS-232C Interface Audio menuPin No Signal Interface specificationsExample of wiring connections Communication parametersReceiving format from VTR to personal computer External interface specificationsSending format from personal computer to VTR Data format Communication system Asynchronous, full duplex Baud rateSTX QOP ETX ACK STX OEJ ETX STX QCD ETX ACK STX CD VTR operation mode Code Command list Key commandsStatus command Send Description of operationDeck ID command Counter sense commandStandby OFF commands Error No Description of errorSet the VTR to the remote mode Video Head CleaningMaintenance CondensationDigital video Input connectorsOutput connectors Line IN/line OUTService Centers