Panasonic AJ-D230HP operating instructions Memory Mode menu, Tape Protect menu

Page 27

Set-up Menus

MEMORY MODE menu

Item

No.	S u p e r i m p o s e d	No.
	d i s p l a y

	300 MEMORY	0000
	300 MEMORY	0001
	MODE	0001
	MODE	0002
		0002
		0003

Setting

S u p e r i m p o s e d d i s p l a y

OFF

MEM STOP REPEAT 1 CONTINUE

Description of settings

This sets the memory operation.

0:No memory operation.

1:The tape stops near the BEGIN point when it is fast forwarded or rewound.

2:When the tape reaches the end, it is rewound to the BEGIN point where it stops.

3:When the tape reaches the end, it is rewound to the BEGIN point where it is played, and this process is repeated.

301 BGN/END PRESET

This sets the BEGIN point and END point.

The underlined number and item are the factory settings.

TAPE PROTECT menu

Item

No.	S u p e r i m p o s e d	No.
No.	d i s p l a y	No.
400	STILL TIMER	0000
		0001
		0002

0003

0004

0005

401SRC PROTECT 0000 0001

402DRUM STDBY 0 0 0 0001

403 STOP	0000
PROTECT	0001

Setting	Description of settings
S u p e r i m p o s e d	Description of settings
d i s p l a y	This selects the time taken until the unit is set to the
0.5S	This selects the time taken until the unit is set to the
5S	tape protection mode when it has been left standing in
10S	the stop, play pause or still mode.
30S (Units: S = seconds, MIN = minutes)
1MIN	The setting for the time taken until the unit is set to

2MIN	the tape protection mode when it has been left
	standing in the REC PAUSE mode is fixed at 2
	minutes.

STEP This sets the tape protection operation which is HALF performed when the unit has been left standing in the

pause mode.

0:Step (step FWD in the still or pause mode; step REV in the REC pause mode)

1:Half loading (standby OFF)

OFF	This sets whether or not the drum is to be stopped in
ON	the STANDBY OFF mode.
	0: The drum rotates at all times.
	1: The drum is stopped in the STANDBY OFF mode.
STEP	This sets the tape protection operation to be performed
HALF	when the unit is left standing in the STOP mode.
	0: Step
	1: Half loading

The underlined number and item are the factory settings.

<Note>

When using a consumer DV cassette tape, tape protection mode is set after 10 seconds, even if STILL TIMER is set to "30S", "1MIN" or "2MIN".

27

Image 27

Contents Operating Instructions FCC Note Table of Contents RS-232C Interface Introduction FeaturesControls and Their Functions Front PanelCounter display area Cassette slot Power switchLOCAL/MENU/REMOTE switch Input Select switchReset button Volume controlVolume recording level control Remote control connectorConnector section Sync in connector AC in connectorSignal GND terminal Handle Video in connectorUse of Panasonic consumer DV cassette tape is recommended TapesType DescriptionInsert the cassette tape Switching on the power and inserting the cassetteSwitch on the power OperationPrecautions for setting the still timer Stop modeRecording Still-picture playback Pause/still recording back-space assemble recordingPlayback Cue and ReviewUse the Audio OUT Select button to select the desired sound Mode Audio OUT connectors Display tubeFrame advance Sound selectionSet the VTR to the menu mode Repeat playbackMenu screen Set the VTR to the local mode Setting Description of operationOFF MEM Stop Repeat Continue Time Code and User’s Bit Time codeUser’s bit Setting the user’s bit Setting the time codeDisplay changes as shown below Time code and user’s bit playbackDisplay position Operating modeSuperimposed Display Screens Characters displayedUpon completion of the setting, press the SET REC button Set-up Default SettingsChanging a setting SettingSetting Set-up MenusBasic menu Operation menu Description of settingsInterface menu Type Format SEL settingTape Protect menu Memory Mode menuTime Code menu Setting Description of settingsLOW-RF Video menuColor MuteAudio menu RS-232C InterfaceCommunication parameters Interface specificationsExample of wiring connections Pin No SignalCommunication system Asynchronous, full duplex Baud rate External interface specificationsSending format from personal computer to VTR Data format Receiving format from VTR to personal computerSTX QOP ETX ACK STX OEJ ETX STX QCD ETX ACK STX CD Send Description of operation Command list Key commandsStatus command VTR operation mode CodeCounter sense command Standby OFF commandsDeck ID command Description of error Error NoCondensation Video Head CleaningMaintenance Set the VTR to the remote modeLine IN/line OUT Input connectorsOutput connectors Digital videoService Centers