POWER
VCR/TV/CABLE/DBS |
|
| ENTER |
|
|
| |
1 | 2 | 3 |
|
|
|
| 2 |
4 | 5 | 6 | NUMBER |
| |||
7 | 8 | 9 |
|
| 0 |
| 4 |
1
STOP
TV PROG +
TV PROG – 
3
CABLE BOX BRAND NAME | BRAND CODE |
|
|
ARCHER | 01, 05, 17 |
CABLETENNA | 01, 17 |
CABLEVIEW | 15, 16, 17 |
CITIZEN | 15, 16, 17 |
CURTIS | 02 |
DIAMOND | 01, 17 |
GC BRAND | 15, 16, 17 |
GEMINI | 15 |
GENERAL INSTRUMENTS | 01, 04, 06, 11, 12, 15 |
HAMLIN | 10, 18, 23 |
JASCO | 15 |
JERROLD | 01, 04, 06, 11, 12, 15 |
NOVAVISION | 02 |
OAK | 07 |
PANASONIC | 13, 14 |
PULSER | 15, 16, 17 |
RCA | 13, 14 |
REGAL | 10, 18 |
REMBRANDT | 01, 16, 17 |
SAMSUNG | 05, 16, 24 |
SCIENTIFIC ATLANTA | 02 |
SIGMA | 07 |
SL MARX | 05, 16, 17, 24 |
SPRUCER | 13, 14 |
STARGATE | 05, 15, 16, 17, 24 |
TELEVIEW | 05, 16, 24 |
TOCOM | 01, 04, 16 |
UNIKA | 01, 17 |
UNIVERSAL | 16, 17 |
VIDEOWAY | 03, 09 |
ZENITH | 03, 09 |
LG | 26 |
TAIHAN (DEHAN) | 27 |
|
|
E
N
39
Cable Box Multi-Brand
Remote Control
The VCR's remote control can control functions on the brands of cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.
TURN ON THE CABLE BOX
1 Turn the power on using the cable box’s remote control.
SET REMOTE CONTROL
MODE
2 Set the VCR/TV/CABLE/DBS switch on the VCR's remote control to CABLE/DBS.
ENTER CABLE BOX BRAND
3 While holding down POWER on the VCR's remote control, use the NUMBER keys to enter the cable box brand number from the chart at bottom left and then press STOP.
Follow the example shown below.
Check if the cable box's power goes off as it should. If it does, try other operations (☞ step 4).
●Once you have set the remote control to operate the cable box, you don't have to repeat this step until you replace the remote control's batteries.
OPERATE CABLE BOX
4 Press the corresponding button: POWER, TV PROG +/– and NUMBER (TV Muting) keys.
●For some brands of cable box, you must press ENTER after having pressed the NUMBER keys.
●To change the cable box's channel, press TV PROG +/– or the NUMBER keys. (The CH +/– button can be used to change the VCR's channel only.)
●To return the remote to VCR control, set the VCR/TV/ CABLE/DBS switch to VCR.
NOTES:
●Depending on the kind of cable box, there may be cases where some or all functions cannot be operated using the remote control.
●It's not possible to set the remote control for both your cable box and your DBS receiver at the same time; you can only set the remote control to the brand of either one.
●You have to subscribe to a cable service to receive cable channels.
(Ex.) To set remote control to ARCHER 01:
POWER |
| STOP | |
0 | 1 | ||
Release | |||
Hold | Press in succession |
| |
down |
|
|