JVC HR-S8600EK setup guide Load a Cassette, Point, Start Playback, Stop Playback

Page 12

12

BASICOPERATIONS

Playback

Turn on the TV and select the VIDEO channel (or AV mode).

The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.

LOAD A CASSETTE

Making sure the window side is up, the rear label side

is facing you and the arrow on the front of the cassette

1 is pointing towards the recorder. Don’t apply too much

4

STOP/EJECT

 

 

1

 

 

1–:–

2

1 2 3

4 5 6

3

PLAY

JOG

 

 

 

8

PAUSE

SCAN SHUTTLE

 

 

TIME

2

 

 

TV/VCR

 

 

 

pressure when inserting.

 

 

 

The recorder power comes on automatically and the

 

counter is reset to 0:00:00.

 

If the record safety tab has been removed, playback

 

begins automatically.

 

 

 

FIND PROGRAMME START

2

POINT

If the tape is advanced past the start point, press REW

or turn the TIME SCAN SHUTTLE ring to the left.

To go forward, press FF or turn the TIME SCAN

 

SHUTTLE ring to the right.

 

 

3

START PLAYBACK

Press PLAY. "BEST" appears blinking in the recorder's

display panel during automatic tracking (pg. 22).

 

Playback picture quality of LP recordings will not be

 

as high as SP recordings.

7 8 9

0

1

3 2

LAY

2 REW

4

STOP

 

￿

3

4

4

3

FF 2

PAUSE

STOP PLAYBACK

Press STOP on the remote or STOP/EJECT on the

recorder’s front panel. Then press STOP/EJECT to

4 remove the cassette.

INFORMATION

When using the AV connection (pg. 6), initiating playback causes the VCR indicator to light and the TV to automatically enter AV mode. To return the TV to TV mode after playback is complete, press TV/VCR so that the VCR indicator turns off.

*Depending on the type of TV used, TV/VCR button does not always function as described above.

Tape Position Indicator

The tape position indicator appears on screen when, from the Stop mode, you press FF, REW or perform an Index Search. The position of “5” in relation to “0” (beginning) or “+” (end)

shows you where you are on 0 + the tape.

”O.S.D.” (pg. 47) must

be set to “ON”, or the

indicator will not appear. Beginning

3

+ +

1:23:45 REMAIN 2:35

End

Usable cassettes

Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette

into a VHS Cassette Adapter and it can be used just like

any full-sized VHS cassette.

This video recorder can record on regular VHS and

Super VHS cassettes. While only VHS signals can be

NOTE:

Depending on the type of tape used, there may be times when the indication is not correct.

recorded on regular VHS cassettes, both VHS and Super

VHS signals can be recorded and played back using

Super VHS cassettes.

Image 12
Contents HR-S8600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderBack of TV Audio in connectors Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemRemote control while downloading is Shows either the display as illustrated on10 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkPlayback Load a CassettePoint Start PlaybackPlayback Activate HIGH-SPEED SearchStill Picture/Frame-By-Frame Playback Slow MotionRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemRecording PlaybackOr press Record on the recorder During B.E.S.TPlayback Picture Adjustment Manual TrackingDigital TBC/NR Digital 3RLooking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsAudio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan TimeScan AudioSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillAccess Main Menu Selecting Sound You WantControl Screen Return to Normal ScreenReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionDuring Playback Type of Broadcast On-screen Display Being ReceivedConnector TV Aerial cable Connector Audio in connectorsAutomatic Satellite Programme Recording Satellite Receiver UnitREC Link indicator Move the highlight bar pointer to Mode SET byLink indicator lights up and the recorder turns off Before performing the following stepsSET Remote Control RE-SUPPLY PowerRemote A/B Code Switching Remote Con- trol FunctionsTV Multi-brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code Operate TVSatellite Receiver Multi- Brand Remote Control Operate Satellite ReceiverTV Prog +/-,NUMBER keys Satellite Tuner Brand CodeAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Connector Lanc Cable not provided To Lanc connector Synchro EditingRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingSET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingRandom As- semble Editing Prepare for EditingLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A. Edit END R.A. EditReset the Counter Insert EditingLocate END Point Engage Insert Editing Start EditingEND Insert Editing Terminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen Information On J TerminalAccess Mode SET ENABLE/DISABLEOther Functions ON-SCREEN DisplayPower Save Mode ModeAuto SP→LP Timer Auto TimerNext Function Memory Engage RECORD-PAUSE Mode Resume RecordingRepeat Playback RetakeConnection To Stereo System Audio Cable not provided SpeakerAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionTuner Set Perform Auto Channel SETAuto Channel Set Screen preset positions After Scan CompletedIs displayed on the screen For about 5 seconds, aStoring Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation ScreenChange Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Access Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopIndex Front ViewRear View @ # $ %Remote Control Remote Control LCD How To UseEMO Memo Maximum recording time DA4 Double Azimuth helicalVHF 44.5 143/143 470 MHz