40ADVANCEDOPERATIONS(cont.)
AV1 SELECT Setting
Set "AV1 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 IN/OUT connector of this recorder.
1Press MENU to access the Main Menu screen.
2Press %Þ to move the highlight bar (pointer) to "MODE SET", then press OK or #.
3 Press %Þ to move the highlight bar (pointer) to "AV1 SELECT". 4 Press OK or #to select "VIDEO" or
: If a connected device's output is compatible only with regular video signals, | |
| set "AV1 SELECT" to "VIDEO". |
: If a connected device's output is compatible with Y/C signals, set "AV1 | |
| SELECT" to |
| quality |
5Press MENU to return to normal screen.
●If "AV2 SELECT" is set to "DECODER", it is impossible to set "AV1 SELECT" to
MODE SET |
|
|
|
| |
B. E. S. T. | ON |
|
PICTURE CONTROL | AUTO |
|
AUTO TIMER | OFF | |
O. S. D. | ON | |
DIRECT REC | ON | |
AUTO SP=LP TIMER | OFF | |
DIGITAL 3R | ON | |
NEXT PAGE |
|
|
[5°] = |
|
|
[MENU] : EXIT |
|
|
PREVIOUS PAGE |
|
|
POWER SAVE | OFF | |
AUTO | ||
AV1 SELECT | VIDEO |
|
AV2 SELECT | AV2 |
|
TIME SCAN AUDIO | ON | |
|
|
|
[5°] = |
|
|
[MENU] : EXIT |
|
|
AV2 SELECT Setting
Set "AV2 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV2 IN/DECODER connector of this recorder.
1Press MENU to access the Main Menu screen.
2Press %Þ to move the highlight bar (pointer) to "MODE SET", then press OK or #.
3 Press %Þ to move the highlight bar (pointer) to "AV2 SELECT". 4 Press OK or #to select "AV2", "DECODER" or "SAT".
| : To use this recorder as the recording deck with the player connected to the |
| AV2 IN/DECODER connector, or to use the satellite receiver connected to |
| the AV2 IN/DECODER connector. |
: To use a decoder connected to the AV2 IN/DECODER connector. | |
: To view a satellite programme with the TV set while the recorder is in Timer | |
| mode, in Stop mode, recording or turned off. (☞ pg. 30) |
5Press MENU to return to normal screen.
●If you have a satellite receiver or a decoder connected to the AV2 IN/DECODER connector, be sure to set "AV2 SELECT" back to appropriate mode after editing.
●If you're not connecting a satellite receiver or a decoder to the AV2 IN/DECODER connector, leave "AV2 SELECT" set to "AV2".
●The default setting is "AV2"; if the recorder's memory backup has expired due to a power cut or because the AC was removed from the recorder, "AV2" will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set "AV2 SELECT" back to appropriate mode.
●If the AV1 OUT switch on the rear panel is set to Y/C, it is impossible to set "AV2 SELECT" to "DECODER".
MODE SET |
|
|
|
| |
B. E. S. T. | ON |
|
PICTURE CONTROL | AUTO |
|
AUTO TIMER | OFF | |
O. S. D. | ON | |
DIRECT REC | ON | |
AUTO SP=LP TIMER | OFF | |
DIGITAL 3R | ON | |
NEXT PAGE |
|
|
[5°] = |
|
|
[MENU] : EXIT |
|
|
PREVIOUS PAGE |
|
|
POWER SAVE | OFF | |
AUTO | ||
AV1 SELECT | VIDEO | |
AV2 SELECT | AV2 |
|
TIME SCAN AUDIO | ON |
|
|
|
|
[5°] = |
|
|
[MENU] : EXIT |
|
|