JVC HR-S8600EK Engage RECORD-PAUSE Mode, Resume Recording, Repeat Playback, Retake, Ntsc Playback

Page 50

50

ADVANCEDOPERATIONS(cont.)

1–:–

2

1 2 3

45 6

78 9

0

1

2

REW

STOP

￿

3

4

4

3

FF

PAUSE

Repeat Playback

Your video recorder can automatically play back the whole tape 50 times repeatedly.

1

 

START PLAYBACK

 

Press PLAY.

2

 

ACTIVATE REPEAT PLAYBACK

 

Press PLAY and hold for over 5 seconds, then release.

 

The Play indicator ( ) on the display panel blinks

 

 

 

 

slowly.

 

 

The tape plays 50 times automatically, and then stops.

 

 

 

3

 

STOP PLAYBACK

 

Press STOP at any time to stop playback.

Retake

You can cut out unnecessary parts of a TV programme while you're recording it.

End of programme

Beginning of programme

 

 

 

 

Programme

Unnecessary

Unnecessary

Programme

 

part

part

 

 

 

 

 

Recorded part

Go back to end of programme to cut out unnecessary part

ENGAGE RECORD-PAUSE MODE

1 Press PAUSE during recording.

LOCATE START POINT

2 Turn the JOG dial to the left or right (or hold down REW or FF) and release it when you reach the point where you want to resume recording.

* Your recorder returns to the Record-Pause mode.

RESUME RECORDING

3 Press PLAY when you wish to resume recording.

NOTE:

NOTE:

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

LOAD A CASSETTE

1 Insert a cassette recorded in NTSC.

START PLAYBACK

2 Press PLAY.

"NTSCPAL" appears on the screen for about 5 seconds.

Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

The counter and tape remaining time readings will be incorrect.

During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

Retake function does not work during Direct Rec (pg. 11).

Image 50
Contents HR-S8600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderBack of TV Audio in connectors Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to item10 or If -- appears on the display panel, refer Remote control while downloading isShows either the display as illustrated on Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackStill Picture/Frame-By-Frame Playback PlaybackActivate HIGH-SPEED Search Slow MotionRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillControl Screen Access Main MenuSelecting Sound You Want Return to Normal ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAutomatic Satellite Programme Recording ConnectorTV Aerial cable Connector Audio in connectors Satellite Receiver UnitLink indicator lights up and the recorder turns off REC Link indicatorMove the highlight bar pointer to Mode SET by Before performing the following stepsRemote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Satellite Tuner Brand CodeSelect Picture Control SET Mode Access Main Menu ScreenAccess Mode SET Screen Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not provided To Lanc connectorSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingEngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingRandom As- semble Editing Prepare for EditingStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Access Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Mode SETENABLE/DISABLE ON-SCREEN DisplayPower Save Mode ModeNext Function Memory Auto SP→LP TimerAuto Timer Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aEnter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopIndex Front ViewRear View @ # $ %Remote Control Remote Control LCD How To UseEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical