JVC HR-S8600EK setup guide Timer Warning, PDC Recording

Page 17

 

SET TAPE SPEED

4 Press SP/LP ( ) to set the tape speed.

5

SET PDC MODE

Press PDC to select "ON" or "OFF".

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

 

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

 

☞ "PDC Recording" in the column below.

 

● VPS (Video Programme System) recording is not

 

currently available in the U.K. and not possible with

 

this recorder.

 

RETURN TO NORMAL SCREEN

 

Press PROG or OK. "PROGRAM COMPLETED" appears

6 on the screen for about 5 seconds, then normal screen

17

Satellite Receiver Users

To timer-record a satellite broadcast using VIDEO Plus+: 1 Set "AV2 SELECT" to the appropriate mode. (☞ pg. 40) 2 Perform steps 1 – 7.

3 Set the satellite receiver to the appropriate channel before the selected programme begins.

4 Leave the satellite receiver's power on.

ATTENTION

Regarding Guide Program Number Set

"GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.

● Press the NUMBER keys or %Þ to input the preset position number on which your recorder receives that station, then press OK or # to set the Guide Program Number. The VIDEO Plus+ Program screen appears.

 

appears.

 

 

 

● Repeat steps 1 – 6 for each additional programme.

 

 

 

ENGAGE RECORDER’S TIMER

7

MODE

Press ä (TIMER). The recorder turns off automatically

and ä appears on the display panel.

 

● To disengage the timer, press ä (TIMER) again.

GUIDE PROG SET

GUIDE PROG

TV PROG

2

– –

[5°] =

 

[PROG] : EXIT

 

(Ex.) To timer-record a BBC2 programme with VIDEO Plus+.

*If your recorder receives BBC2 on the preset position 2, press OK or #after entering "2".

NOTES:

● To Change The Stop Time . . .

. . . press STOP +/– in step 3. You can compensate for

anticipated programme schedule delays this way.

● To Timer-Record Weekly Or Daily Serials . . .

. . . in step 3, press WEEKLY (NUMBER key “9”) for weekly

serials or DAILY (NUMBER key “8”) for daily serials (Monday

– Friday). Either "WEEKLY" or "DAILY" appears on the screen.

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

Pressing the button again makes the corresponding indication

disappear.

● You can programme this recorder to timer-record as many as 8

programmes. If you try to programme the recorder to record a

ninth, "PROGRAM FULL" appears on screen and "FULL"

appears on the front display panel. To record the extra

programme, you must first cancel any unnecessary

programmes (☞ pg. 20).

● It is not possible to timer-record a TV programme with a

PlusCode number which starts with "0".

NOTES:

●The warning only appears if you’re not in the Timer mode at the time.

●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in most areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (☞ step 5 above).

NOTES:

●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN/DECODER on your recorder.

●PDC recording is also possible via the AV1 IN/OUT connector.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents HR-S8600EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Back of TVMains outlet Mains Power Cord Back of TV Audio in connectorsGo to item Before performing the following procedure, make sure thatShows either the display as illustrated on Remote control while downloading is10 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackStill Picture/Frame-By-Frame Playback Slow MotionRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsPlayback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillSelecting Sound You Want Access Main MenuControl Screen Return to Normal ScreenSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedTV Aerial cable Connector Audio in connectors ConnectorAutomatic Satellite Programme Recording Satellite Receiver UnitMove the highlight bar pointer to Mode SET by REC Link indicatorLink indicator lights up and the recorder turns off Before performing the following stepsRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlTV Prog +/-,NUMBER keys Satellite Tuner Brand CodeAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not provided To Lanc connectorSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV2 Select Setting AV1 Select SettingLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingPrepare for Editing Random As- semble EditingLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Access Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayMode Power Save ModeNext Function Memory Auto SP→LP TimerAuto Timer Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aInput Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View Index@ # $ % Rear ViewRemote Control How To Use Remote Control LCDEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical
Top Page Image Contents