JVC HR-S8600EK setup guide Recording, Playback, Or press Record on the recorder, During B.E.S.T

Page 23

Recording

1

START RECORDING

Press and hold RECORD and press PLAY on the remote,

or press RECORD on the recorder.

 

DURING B.E.S.T.

 

 

 

 

B.E.S.T. COMPLETE

The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.

NOTES:

The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

The B.E.S.T. system does not work while Auto Satellite Prog recording is in progress (pg. 30).

In the case of timer recording, the B.E.S.T. system works before recording is initiated.

Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed.

Pressing the recorder's RECORD button while "BEST" is displayed does not start Instant Timer Recording (pg. 15).

ATTENTION

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

1)Press and hold PAUSE and press RECORD to engage the RECORD PAUSE mode.

The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE.

2)Press PLAY when you are ready to start recording.

If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 4 on page 22.

23

Playback

The recorder assesses the quality of the tape once you initiate playback.

START PLAYBACK

1 Press PLAY.

The recorder adjusts the playback picture quality based on the quality of the tape in use.

B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel.

NOTES:

When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

When watching a rental tape or one recorded on another video recorder, or when using this recorder as the player for editing, set B.E.S.T. to your preference by performing steps 1 through 5 on page 22.

"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.

Image 23
Contents HR-S8600EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Back of TVMains outlet Mains Power Cord Back of TV Audio in connectorsGo to item Before performing the following procedure, make sure thatLink screen will appear. Then the Guide Remote control while downloading isShows either the display as illustrated on 10 or If -- appears on the display panel, referIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notNexTView Link TV Auto Power OnLink Functions Turn on the RecorderStart Playback PlaybackLoad a Cassette PointSlow Motion PlaybackActivate HIGH-SPEED Search Still Picture/Frame-By-Frame PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Enter Programme Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsDuring B.E.S.T RecordingPlayback Or press Record on the recorderDigital 3R Playback Picture AdjustmentManual Tracking Digital TBC/NRSections Looking For Scene You WantActivate Index Search Skip Over UnwantedNormal recorder Audio signal during TimeScanTimeScan Variable-Speed Search/ Reverse PlayForward Search Play Slow-Motion Still TimeScanTimeScan Audio Speed SP Speed LP Audio outputReturn to Normal Screen Access Main MenuSelecting Sound You Want Control ScreenType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackSatellite Receiver Unit ConnectorTV Aerial cable Connector Audio in connectors Automatic Satellite Programme RecordingBefore performing the following steps REC Link indicatorMove the highlight bar pointer to Mode SET by Link indicator lights up and the recorder turns offRemote Con- trol Functions SET Remote ControlRE-SUPPLY Power Remote A/B Code SwitchingOperate TV TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSatellite Tuner Brand Code Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver TV Prog +/-,NUMBER keysMinimizing Picture Degradation While Editing Access Main Menu ScreenAccess Mode SET Screen Select Picture Control SET ModeEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not provided To Lanc connectorSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV2 Select Setting AV1 Select SettingStart Dubbing SET Input ModeLocate Start Point Engage Audio DubbingPrepare for Editing Random As- semble EditingEND R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Access Jlip ID NO. SET ScreenON-SCREEN Display Access Mode SETENABLE/DISABLE Other FunctionsMode Power Save ModeNext Function Memory Auto SP→LP TimerAuto Timer Retake Engage RECORD-PAUSE ModeResume Recording Repeat PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Test SignalAuto Channel Set Tuner SetPerform Auto Channel SET For about 5 seconds, a Screen preset positionsAfter Scan Completed Is displayed on the screenClose Confirmation Screen Storing Channels ManuallyInput Channel Enter NEW Channel InformationDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access ManualSwitch Stations Channel SET ScreenStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View Index@ # $ % Rear ViewRemote Control How To Use Remote Control LCDEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical