JVC HR-S8600EK Activate HIGH-SPEED Search, Still Picture/Frame-By-Frame Playback, Slow Motion

Page 13

Still Picture/Frame-By-Frame Playback

1

 

PAUSE DURING PLAYBACK

 

Press PAUSE.

 

 

 

During still picture, the sound from the previous

 

3 seconds (approx.) will be played back repeatedly

 

 

(provided there was at least 6 seconds of normal

 

 

playback prior to engaging the still picture mode).

 

 

"TIME SCAN AUDIO" must be set to "ON", or the

 

 

sound will not be heard. (pg. 27)

 

 

 

 

 

ACTIVATE FRAME-BY-FRAME

2

 

PLAYBACK

 

Turn the JOG dial to the right for forward frame-by-

 

frame playback, or to the left for reverse frame-by-frame

 

playback.

 

OR

 

 

Press PAUSE.

 

OR

 

 

Press @ or #.

 

 

 

To resume normal playback, press PLAY.

Slow Motion

ACTIVATE SLOW-MOTION PLAYBACK

1 Turn the TIME SCAN SHUTTLE ring to the left or press @during playback to decrease speed in the forward direction. To play in reverse slow-motion (and in reverse play mode), continue to turn the TIME SCAN SHUTTLE ring to the left or press @after selecting all the forward direction slow-motion modes.

OR

During still picture, turn the TIME SCAN SHUTTLE ring to the right for forward slow motion, or to the left for reverse slow motion.

OR

During still picture, press and hold PAUSE for 2 seconds, then release. Press and release again to return to still picture.

OR

During still picture, press and hold @ or #. Release to return to still picture.

To resume normal playback, press PLAY.

NOTE:

13

High-Speed (Turbo) Search

ACTIVATE HIGH-SPEED

SEARCH

1 During playback or still, press FF for forward high- speed search, or REW for reverse high-speed search.

To resume normal playback, press PLAY.

NOTE:

For short searches, press and hold FF or REW during playback or still picture. When released, normal playback resumes.

ATTENTION

In the high-speed search, still, slow-motion or frame-by- frame playback mode,

the picture will be distorted.

noise bars will appear.

there will be a loss of colour with a tape recorded in LP mode.

Picture may not appear during high-speed search with a tape recorded in LP mode.

When normal playback resumes from search, still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

For Time Jog, see page 27.

Image 13
Contents HR-S8600EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Back of TVMains outlet Mains Power Cord Back of TV Audio in connectorsGo to item Before performing the following procedure, make sure thatShows either the display as illustrated on Remote control while downloading is10 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackStill Picture/Frame-By-Frame Playback Slow MotionRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsPlayback RecordingOr press Record on the recorder During B.E.S.TManual Tracking Playback Picture AdjustmentDigital TBC/NR Digital 3RActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsTimeScan Audio signal during TimeScanVariable-Speed Search/ Reverse Play Normal recorderTimeScan Audio TimeScanSpeed SP Speed LP Audio output Forward Search Play Slow-Motion StillSelecting Sound You Want Access Main MenuControl Screen Return to Normal ScreenSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesDuring Playback Type of Broadcast On-screen Display Being ReceivedTV Aerial cable Connector Audio in connectors ConnectorAutomatic Satellite Programme Recording Satellite Receiver UnitMove the highlight bar pointer to Mode SET by REC Link indicatorLink indicator lights up and the recorder turns off Before performing the following stepsRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlTV Prog +/-,NUMBER keys Satellite Tuner Brand CodeAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Synchro Editing Connector Lanc Cable not provided To Lanc connectorRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV2 Select Setting AV1 Select SettingLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingPrepare for Editing Random As- semble EditingLocate EDIT-OUT Point Locate EDIT-IN PointStart R.A. Edit END R.A. EditInsert Editing Reset the CounterLocate END Point Start Editing Engage Insert EditingEND Insert Editing Access Initial SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Jlip ID NO. SET Screen Information On J TerminalENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayMode Power Save ModeAuto Timer Auto SP→LP TimerNext Function Memory Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalPerform Auto Channel SET Tuner SetAuto Channel Set After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aInput Channel Storing Channels ManuallyEnter NEW Channel Information Close Confirmation ScreenFine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListTV Station Channel Number Guide Just Clock Clock SetNumber Video Plus+ SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View Index@ # $ % Rear ViewRemote Control How To Use Remote Control LCDEMO Memo DA4 Double Azimuth helical Maximum recording timeVHF 44.5 143/143 470 MHz