JVC HR-S8600EK Safety Precautions, Connection to the mains supply in the United Kingdom

Page 2

2

SAFETYFIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

IMPORTANT

■Please read the various precautions on p. 2 – 4 of this instruction manual before installing or operating the recorder.

■It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

IMPORTANT

Connection to the mains supply in the United Kingdom.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/ adapter or consult your dealer.

In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.

If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green.

The wires in the mains lead are coloured in accordance with the following code:

Blue to N (Neutral) or Black

Brown to L (Live) or Red

If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured Black.

Brown wire to terminal coded L (Live) or coloured Red.

If in doubt — consult a competent electrician.

625

■Cassettes marked "S-VHS" and "VHS" can be used with this video cassette recorder. However, S-VHS recordings are possible only with cassettes marked "S-VHS".

■VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO Plus+ system is manufac- tured under license from Gemstar Development Corporation.

Image 2

Contents HR-S8600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Back of RecorderBack of TV Audio in connectors Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to item10 or If -- appears on the display panel, refer Remote control while downloading isShows either the display as illustrated on Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackStill Picture/Frame-By-Frame Playback PlaybackActivate HIGH-SPEED Search Slow MotionRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback During B.E.S.TDigital TBC/NR Playback Picture AdjustmentManual Tracking Digital 3RSkip Over Unwanted Looking For Scene You WantActivate Index Search SectionsVariable-Speed Search/ Reverse Play Audio signal during TimeScanTimeScan Normal recorderSpeed SP Speed LP Audio output TimeScanTimeScan Audio Forward Search Play Slow-Motion StillControl Screen Access Main MenuSelecting Sound You Want Return to Normal ScreenDuring Playback Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedAutomatic Satellite Programme Recording ConnectorTV Aerial cable Connector Audio in connectors Satellite Receiver UnitLink indicator lights up and the recorder turns off REC Link indicatorMove the highlight bar pointer to Mode SET by Before performing the following stepsRemote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Satellite Tuner Brand CodeSelect Picture Control SET Mode Access Main Menu ScreenAccess Mode SET Screen Minimizing Picture Degradation While EditingEdit From Camcorder Repeat steps 4 6 as necessary Connector Lanc Cable not provided To Lanc connectorSynchro Editing Edit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingEngage Audio Dubbing SET Input ModeLocate Start Point Start DubbingRandom As- semble Editing Prepare for EditingStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point END R.A. EditLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Access Jlip ID NO. SET Screen Terminal JLIPJoint Level Interface Protocol ConnectorAccess Initial SET Screen Information On J TerminalOther Functions Access Mode SETENABLE/DISABLE ON-SCREEN DisplayPower Save Mode ModeNext Function Memory Auto SP→LP TimerAuto Timer Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionAuto Channel Set Tuner SetPerform Auto Channel SET Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aEnter NEW Channel Information Storing Channels ManuallyInput Channel Close Confirmation ScreenDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List Station NameTV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopIndex Front ViewRear View @ # $ %Remote Control Remote Control LCD How To UseEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical