Lexicon 960L owner manual Loading Registers, Alternative Loading Techniques, Programming Machines

Page 30

Operations in Detail

Lexicon, Inc.

Loading Programs and Registers, continued

Loading Registers

Loading Registers is similar to loading Programs. Press the REGISTER Key instead of the PROGRAM Key. This will bring up a similar screen (Fig. 4-2) The only differences are the use of the word "Register" instead of "Program" and the addition of two soft buttons for labeling. Note also that the last two Registers are unnamed and greyed out on the display, indicating that they’re empty. Any selection that is greyed out, on any

screen, is unavailable. Programs and Registers can be unavailable if they are empty or if they are designed for sample rates and configurations that are not currently selected.

Shortcut: You can instantly load any Program or Register in the current Bank by pressing the corresponding key on the Numeric Keypad.

Figure 4-2 — Register Load screen

Alternative Loading Techniques

•You can use the Left/Right Navigation Arrows to move between Banks and Programs (or Banks and Registers).

•You can use the +/- Buttons or the Up/Down Navigation Arrows to scroll through Banks.

•You can use the +/- Buttons or the Up/Down Navigation Arrows to scroll though Programs and Registers. Press the ENTER key to load the Program.

•You can repeatedly press BANK, PROGRAM or REGISTER to scroll through the Banks, Programs and Registers.

Programming Machines

Depending on the configuration (see below), the 960L can be used as one, two, or four processing machines. The number of machines available in the current configuration is shown on the Machine Strip in the System Status Display. The machine whose settings you are

currently altering is highlighted. Machines that are muted have a blinking red "M" super- imposed on their machine number.

You must program each machine individually. To switch to a different machine, press and hold the MACHINE key, then enter the desired machine number on the Numeric Keypad.

4-2

Image 30

Contents 960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Introduction Title of SectionMainframe About the 960L DescriptionRear Panel Unpacking the 960LMains Power Switch Clock Card Midi Connectors Five-pin DIN femaleRemote-Control Connectors IEC Power ConnectorFloppy Drive Standby Switch and IndicatorFront Panel ThumbscrewsBehind the Front Panel DSP-Card SlotsCPU Card Ventilation InstallationMounting LocationDigital Audio Connections Midi ConnectionsWordclock Connections LARC2 Remote Navigating Typical Display ScreensLARC2 Remote About the LARC2Unpacking the Larc LARC2 Control Surface LARC2 Control SurfaceGetting What You Want LARC2 ConnectionsNavigating Typical Display Screens A typical display screenMode Faders Joystick About the Faders and JoystickAudio Indicators Fine AdjustLexicon Button Basic Operation AN Overview of the ControlsBasic Operation An Overview of the ControlsSetup Control Mode Quick Guide to Operation960L Owner’s MaunalBasic Operations Quick Guide to Operation Machine Selection Program LoadingEditing a Program or Register Storing Your EditsName screen Info screens are similar Control Mode CLOCKS, Configuration Operations in DetailLoading Programs and Registers Loading ProgramsLoading Registers Alternative Loading TechniquesProgramming Machines Control Mode Clocks, Configuration, and System Screens WordclockInput, Output, and Machine Configuration Locked and unlocked wordclock960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround Analog and Digital I/O System ScreenEditing Algorithms Fine AdjustEditing Editing With the FadersEditing with the Joystick Quick Comparisons via the Lexicon ButtonEditing Inputs and Outputs Input PanningOutput Panning Setting Levels 960L Surround Panning RulesAvoiding Overload Using the Edit Algorithm Screen V-Page and Parameter ReassignmentFrom the Edit Algorithm, Inputs, Outputs Options screen 22 Edit V-Page screen programming the joystick Storing and Labeling Your Edits StoringNaming and Annotating 25 a Register Info Options Enabled Organizing Your RegistersCD-ROM Machine ModeUsing the Floppy Drive Edit Tools for RegistersUsing the Reverb Programs Using the Reverb Programs Reverberation and RealityUsing The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Algorithms Random HallPlate & Surround Plate Surround HallChamber Ambience & Surround AmbienceAmbient Chamber Reverse & Surround ReverseInverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckLF FbckLFbckR FbckLSLvLR LvLLLvRR LvRL LvLFLFRShape RearRollRearRvb RSpreadSpin SizeSlope SpreadMidi Nomenclature Midi Channel AllocationChannel Usage Description Bank Description Card ConfigurationBank and Program Mapping Program # DescriptionMidi Sysex Incoming Inquiry Midi Byte Description960Ls response Midi Implementation Chart Specifications Specifications 96K Connector48K Rack Units Factory ProgramsLARC2 User Interface Appendix Appendix Program Descriptions HallsAppendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?