Lexicon 960L owner manual Bank and Program Mapping, Bank Description, Card Configuration

Page 64

MIDI	Lexicon, Inc.

MIDI, Continued

Program Loading

Because of the large number of potential Programs in the 960L, Program Change messages are used along with the Bank Select extension to provide MIDI Program selection. Controllers 0 and 32 are sent to the system, followed by a Program Change message to select a program. In this method, Controller 0 provides the most-significant 7 bits of the Bank and Controller 32 provides the least-significant 7 bits. The Program within a Bank is selected with a Program Change message. Each Bank has 10 programs or less, so only Program Changes 0 – 9 will cause a program load.

The Bank values are "sticky", that is, the 960L will remember the Bank values for each MIDI channel. It is not necessary to send a Bank change with each Program Change unless the Bank has indeed changed. This is in full conformance the MIDI specification.

Bank and Program Mapping

There are 10 Programs or fewer in each Bank. Bank and Program Changes out of range will be ignored.

Bank	Description

0-19	Factory Preset (Controller 0 = 0; Controller 32 = 0-19)

2048-2147	User Registers (Controller 0 = 16; Controller 32 = 0-99)

8192	Floppy Disk (Controller 0 = 64; Controller 32 = 0-9)

16383 (highest Bank)	Card configuration. For Channel 1 (DSP card) only.

Card Configuration

The DSP card is partitioned through Program Change messages on channel 1. The highest Bank number

(16383, 0x7f on Controller 0 and 0x7f on Controller 32) is used for this purpose. Other Bank numbers are reserved for future use. Here are the values:

Program #	Description

0	Stereo (4 stereo machines at 48K. 2 at 96K)

1	Surround (5-in/5-out plus 2-in/5-out at 48K. 5-in/5-out at 96K)

2	Surround (dual 2-in/5-out at 48K. Single 2-in/5-out at 96K)

63	8-channel. Useful for wiring checks and diagnostics.

Continuous Controllers

The 960L does not respond to continuous controllers, except those used for Bank change.

6-2

Image 64

Contents 960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Introduction Title of SectionMainframe Description Rear PanelAbout the 960L Unpacking the 960LClock Card Midi Connectors Five-pin DIN female Remote-Control ConnectorsMains Power Switch IEC Power ConnectorStandby Switch and Indicator Front PanelFloppy Drive ThumbscrewsDSP-Card Slots Behind the Front PanelCPU Card Installation MountingVentilation LocationMidi Connections Digital Audio ConnectionsWordclock Connections LARC2 Remote Navigating Typical Display ScreensAbout the LARC2 LARC2 RemoteUnpacking the Larc LARC2 Control Surface LARC2 Control SurfaceGetting What You Want LARC2 ConnectionsNavigating Typical Display Screens A typical display screenMode Faders Joystick About the Faders and JoystickFine Adjust Audio IndicatorsLexicon Button Basic Operation AN Overview of the ControlsBasic Operation An Overview of the ControlsSetup Control Mode Quick Guide to Operation960L Owner’s MaunalBasic Operations Quick Guide to Operation Machine Selection Program LoadingEditing a Program or Register Storing Your EditsName screen Info screens are similar Control Mode CLOCKS, Configuration Operations in DetailLoading Programs and Registers Loading ProgramsAlternative Loading Techniques Loading RegistersProgramming Machines Control Mode Clocks, Configuration, and System Screens WordclockInput, Output, and Machine Configuration Locked and unlocked wordclock960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround Analog and Digital I/O System ScreenFine Adjust EditingEditing Algorithms Editing With the FadersEditing with the Joystick Quick Comparisons via the Lexicon ButtonEditing Inputs and Outputs Input PanningOutput Panning 960L Surround Panning Rules Setting LevelsAvoiding Overload V-Page and Parameter Reassignment Using the Edit Algorithm ScreenFrom the Edit Algorithm, Inputs, Outputs Options screen 22 Edit V-Page screen programming the joystick Storing Storing and Labeling Your EditsNaming and Annotating 25 a Register Info Options Enabled Organizing Your RegistersMachine Mode Using the Floppy DriveCD-ROM Edit Tools for RegistersUsing the Reverb Programs Using the Reverb Programs Reverberation and RealityUsing The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Algorithms Random HallSurround Hall ChamberPlate & Surround Plate Ambience & Surround AmbienceReverse & Surround Reverse Ambient ChamberInverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckL FbckRFbckLF FbckLSLvLL LvRRLvLR LvRL LvLFLFRearRoll RearRvbRShape RSpreadSize SlopeSpin SpreadMidi Midi Channel Allocation NomenclatureChannel Usage Description Card Configuration Bank and Program MappingBank Description Program # DescriptionIncoming Inquiry Midi Byte Description Midi Sysex960Ls response Midi Implementation Chart Specifications Specifications Connector 48K Rack Units96K Factory ProgramsLARC2 User Interface Appendix Appendix Program Descriptions HallsAppendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?