Lexicon 960L owner manual Important Safety Instructions

Page 2

Important Safety Instructions

Save these instructions for later use.

Follow all instructions and warnings marked on the unit.

Always use with the correct line voltage. Refer to the manufacturer's operating instructions for power requirements. Be advised that different operating voltages may require the use of a different line cord and/or attachment plug.

Do no install the unit in an unventilated rack, or directly above heat producing equipment such as power amplifiers. Observe the maximum ambient operating temperature listed in the product specification.

Slots and openings on the case are provided for ventilation; to ensure reliable operation and prevent it from overheating, these openings must not be blocked or covered. Never push objects of any kind through any of the ventilation slots. Never spill a liquid of any kind on the unit.

This product is equipped with a 3-wire grounding type plug. This is a safety feature and should not be defeated. Never attach audio power amplifier outputs directly to any of the units connectors.

To prevent shock or fire hazard, do not expose the unit to rain or moisture, or operate it where it will be exposed to water. Do not attempt to operate the unit if it has been dropped, damaged, exposed to liquid, or if it exhibits a distinct change in performance indicating the need for service.

This unit should only be opened by qualified service personnel. Removing covers will expose you to hazardous voltages.

Notice

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in Part 15 of FCC Rules, which are designated to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna

Relocate the units with respect to the receiver Move the units away from the receiver

Plug the unit into a different outlet so that the unit and receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful:

"How to identify and Resolve Radio/TV interference Problems"

This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.

This triangle alerts you to important

 

 

This triangle, which appears on your component,

operating and maintenance

 

 

alerts you to the presence of uninsulated,

CAUTION

 

instructions in this

 

dangerous voltage inside the enclosure;

accompanying

 

 

voltage that may be sufficient to

RISK OF ELECTRIC SHOCK

literature

constitute a risk of shock.

DO NOT OPEN

 

 

 

 

 

 

"Dolby", "Dolby Surround", "Pro Logic", and "Dolby Digital" are trademarks of Dolby Laboratories. "Super Audio CD" and "SACD" are trademarks of Sony Electronics, Inc. "THX" and "Home THX Cinema" are trademarks of Lucasfilm, Ltd.

"Logic7", "LexiconLogic", and "3DPM" are trademarks of Lexicon, Inc.

 

Lexicon Inc.

Copyright © 2000

3 Oak Park

Bedford, MA 01730 USA

All Rights Reserved.

Telephone 781-280-0300

 

Lexicon Part No. 070-14353

Fax 781-280-0490

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 960L. Digital Effects System Important Safety Instructions Table Of Contents Table Of Contents Introduction Title of SectionMainframe About the 960L DescriptionRear Panel Unpacking the 960LMains Power Switch Clock Card Midi Connectors Five-pin DIN femaleRemote-Control Connectors IEC Power ConnectorFloppy Drive Standby Switch and IndicatorFront Panel ThumbscrewsCPU Card Behind the Front PanelDSP-Card Slots Ventilation InstallationMounting LocationWordclock Connections Digital Audio ConnectionsMidi Connections LARC2 Remote Navigating Typical Display ScreensUnpacking the Larc LARC2 RemoteAbout the LARC2 LARC2 Control Surface LARC2 Control SurfaceGetting What You Want LARC2 ConnectionsNavigating Typical Display Screens A typical display screenMode Faders Joystick About the Faders and JoystickLexicon Button Audio IndicatorsFine Adjust Basic Operation AN Overview of the ControlsBasic Operation An Overview of the ControlsSetup Control Mode Quick Guide to Operation960L Owner’s MaunalBasic Operations Quick Guide to Operation Machine Selection Program LoadingEditing a Program or Register Storing Your EditsName screen Info screens are similar Control Mode CLOCKS, Configuration Operations in DetailLoading Programs and Registers Loading ProgramsProgramming Machines Loading RegistersAlternative Loading Techniques Control Mode Clocks, Configuration, and System Screens WordclockInput, Output, and Machine Configuration Locked and unlocked wordclock960L Owner’s Maunal Operations in Detail 44.1/48kHz Dual machines 5-in and 2-in Output Assignment Left Right Center Unused Surround Surround Analog and Digital I/O System ScreenEditing Algorithms Fine AdjustEditing Editing With the FadersEditing with the Joystick Quick Comparisons via the Lexicon ButtonEditing Inputs and Outputs Input PanningOutput Panning Avoiding Overload Setting Levels960L Surround Panning Rules From the Edit Algorithm, Inputs, Outputs Options screen Using the Edit Algorithm ScreenV-Page and Parameter Reassignment 22 Edit V-Page screen programming the joystick Naming and Annotating Storing and Labeling Your EditsStoring 25 a Register Info Options Enabled Organizing Your RegistersCD-ROM Machine ModeUsing the Floppy Drive Edit Tools for RegistersUsing the Reverb Programs Using the Reverb Programs Reverberation and RealityUsing The Reverb Program Lexicon, Inc Reverberation and Reality Msec Sound in Space a Short History of Stereo and Surround Algorithms Random HallPlate & Surround Plate Surround HallChamber Ambience & Surround AmbienceInverse Ambient ChamberReverse & Surround Reverse Parameters Used in the 960L Algorithms Using The Reverb ProgramLexicon, Inc FbckLF FbckLFbckR FbckLSLvLR LvLLLvRR LvRL LvLFLFRShape RearRollRearRvb RSpreadSpin SizeSlope SpreadMidi Channel Usage Description NomenclatureMidi Channel Allocation Bank Description Card ConfigurationBank and Program Mapping Program # Description960Ls response Midi SysexIncoming Inquiry Midi Byte Description Midi Implementation Chart Specifications Specifications 96K Connector48K Rack Units Factory ProgramsLARC2 User Interface Appendix Appendix Program Descriptions HallsAppendix B1 P4 B3 P4 B6 P2 B7 P2 B9 P9 B11 P5 Empty Mini Chamber Similar to Snare Chamber, but even smaller Lg Brite Room Random Hall Simply large and bright Echo Plate Like Flat Plate, but with echoes Stereo Bank Kitchen Chamber Can you find your disposal sound effect?
Top Page Image Contents