Pelco c649m operation manual Maintenance Menu, Clock OUT, Rec, Mode OUT, Series

Page 25

CLOCK OUT

Sets the number of frames or fields to record (depending on the

 

recording mode) at the CLOCK OUT terminal. The default is

 

REC.

 

1.

First, set the recording mode for the CLOCK OUT pulse

 

 

output in the Rear Terminal menu.

 

 

• REC – When recording in any mode.

 

 

T/L-REC – When recording in time-lapse mode

 

 

(L18H, L24H, 48H, 72H, 96H, 120H, 168H, or 0H).

 

2.

Second, select the frequency interval by turning the

 

 

SHUTTLE ring. When you turn the JOG dial, the display

 

 

switches in the following order: 1, 2, 3, 4, 5, 10, 15, 20,

 

 

25, 30, 50, 60, F (field), 1. The numbers from 1 to 60

 

 

indicate the number of frames in 2H or 6H recording mode

 

 

or the number of fields in time-lapse recording mode. One

 

 

frame consists of two fields. One field is selected when it

 

 

is set to “F” (field).

MODE OUT

Sets the state in which the signal output at the MODE OUT

 

terminal is switched to active. When you turn the JOG dial, the

 

display switches in the following order: REC (recording), PLAY

 

(playback), POWER (power on), TAPE IN (tape inserted),

 

TAPE REMAIN (three minutes in 2H mode before the tape

 

ends), CLOCK ADJ (output the signal for one second when the

 

clock indicates 00[min]:00[sec]), REC. The default is REC.

REC IN

Sets the REC IN terminal’s operation mode. The default is

 

SERIES.

SERIES – Recording starts when the REC IN terminal is short-circuited to ground or a low-level voltage (0 to +1.6V) is applied.

REC-START/STOP – Recording starts when the REC IN terminal is short-circuited to ground or a low-level voltage (0 to +1.6V) is applied. Recording stops if this connection is removed.

SYNC REC – The video signals from 3 or 13 cameras can be recorded separately by connecting a switcher. (Synchronous recording is available when recording in L18H or L24H mode.) Synchronous recording is explained (and the procedure listed) in Section 8.1.7.

6.9MAINTENANCE MENU

<MAINTENANCE>

POWER LOSS LIST

ALARM LIST

ALL MENU INITIALIZE

POWER LOSS LIST CLEAR

ALARM LIST CLEAR

<REPEAT REC TIMES>

0

<ELAPSED TIME>

0H

Figure 14. Maintenance Menu

POWER LOSS To display the power loss list, turn the JOG dial to select

LISTPOWER LOSS LIST. Turn the SHUTTLE ring to the right to display the list. Power failure start times are stored in memory, so you can confirm when they occurred. Up to three power failure start times will be displayed. If there were more than three, the first and last two power failure start times will be displayed.

ALARM LIST To display the alarm list, turn the JOG dial to select ALARM LIST. Turn the SHUTTLE ring to the right to display the list. Alarm record start times are stored in memory, so you can confirm when they occurred. Up to three alarm record start times will be displayed. If there were more than three, the first and last two alarm record start times will be displayed.

Pelco Manual C649M (7/99)

25

Image 25
Contents TLR2168S Contents Alarm Recording Timer RecordingRecording After a Power Failure Playback Playback Procedure Locating the Start of Alarm RecordingsList of Tables List of IllustrationsRevision History Manual # Date CommentsAvertissement GeneralSAFEGUARDS, WARNINGS, CAUTION, and Care Accessories CleaningPower Sources Power Cord ProtectionInformation Regulatory NoticesUnpacking Instructions Care Of Video Cassette TapeOverview TLR2168S Features and FunctionsIntroduction to TIME-LAPSE Recorders Pelco Manual C649M 7/99 Basic Start Quick StartAdditional Items PRE-INSTALLATION Cautions InstallationInstallation Securing the VCR ControlsAudio Monitor MIC Audio Video OUTFor Alarm Recording a lines in Figure Connecting the VCR to a MultiplexerTIME-LAPSE VCR Coaxial Cable MX4000 Genex Series MultiplexerFront Panel ControlsFluorescent Display Rear Panel This page intentionally left blank General Programming Instructions ProgrammingMain Menu Display Quick Guide to TLR2168S Menu StructureMain Menu Display Menu 6.4.1 Display ModeTime Date Size Background Color Blue BackTime Time Date Search MenuDate DirectionRecording SET UP Menu Timer Program MenuSTART/END RECRear Terminal Menu Mode OUT Maintenance MenuClock OUT RECFirst Time Set Up Menu First Time SET UP MenuDay and Time Display Modes Set the Day and Time OFF Loading LOADING/UNLOADING/PROTECTING the Tape CassetteUnloading Preventing Accidental ErasureManual Recording RecordingRecord Check Function Recording ModeAudio Recording Repeat RecordingNumber of Tape Uses Repeat Recording Times Recording Number of Repeat Tape Uses Time ModeRecommended Number of Tape Uses One-Shot/Interval Recording Series RecordingSync Synchronous RecordingVCR REC REC RECProgramming Procedure Timer RecordingSpecial DW Settings VCRAlarm Recording Avoid Mistakes When Using the TimerSymptom Fault Action External Time Clock Adjustment Alarm Recording Connection1st VCR 2nd VCR Programming For Alarm Recording Reset The Alarm Recording List Alarm Record Time DisplayRecording After a Power Failure Emergency RecordingPlayback Playback ProcedureAudio Playback Playback ModeEnd Of Tape Special Effects PlaybackDirect Shuttle Ring Shuttle RingStill Picture Locating the Start of Alarm RecordingsFrame-by-Frame Playback Index SearchSkip Search Adjustment During Playback 9.4.1 Tracking AdjustmentIf Noise Appears Vertical Adjustment Picture Quality AdjustmentWhen the Picture Is Vibrating SharpMemory Backup in Case of Power Failure Additional Functions and FeaturesPower Failure Time Display CounterElapsed Time Display Initial System Testing TestingRegular System Testing SELF-DIAGNOSTIC Function and Warning Display TroubleshootingFluorescent Monitor Cause Remedy To Turn OFF IndicationSymptom Remedy Before Calling for ServiceALM/CALL/MODE SET/RST/REC CLK SpecificationsRecord Record Time Field Picture Tape Drive Audio Recording GND Pelco Manual C649M 7/99 Pelco Manual C649M 7/99 Warranty Warranty and Return InformationReturns