SUPER MICRO Computer user manual Installing the SuperServer 6012L-6 into a Rack

Page 19

Chapter 2: Server Installation

2-4 Installing the SuperServer 6012L-6 into a Rack

This section provides information on installing the SuperServer 6012L-6 into a rack unit. If the 6012L-6 has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly. The following is a guideline for installing the 6012L-6 into a rack with the rack rails provided. You should also refer to the installation instructions that came with the rack unit you are using.

Identifying the Sections of the Rack Rails:

You should have received two rack rail assemblies with the SuperServer 6012L-6. Each of these assemblies consist of three sections: an inner fixed chassis rail that secures to the 6012L-6 (A) and an outer fixed rack rail that secures directly to the rack itself (B). A sliding rail guide sand- wiched between the two should remain attached to the fixed rack rail. (See Figure 2-1.) The A and B rails must be detached from each other to install.

To remove the fixed chassis rail (A), pull it out as far as possible - you should hear a "click" sound as a locking tab emerges from inside the rail assembly and locks the inner rail. Then depress the locking tab to pull the inner rail completely out. Do this for both the left and right side rack rail assemblies.

Mounting Holes

B

Locking Tab

A

Figure 2-1. Identifying the Sections of the Rack Rails

2-3

Image 19
Contents Super Page About This Manual PrefaceManual Organization Bios System SafetyAdvanced Motherboard Setup Advanced Chassis SetupPreface Table of Contents Advanced Motherboard Setup System SafetyCR5 LED Advanced Chassis SetupAppendices AmibiosPage Overview Chapter Introduction to the SuperServer 6012L-6Control Panel Server Chassis FeaturesSystem Power Scsi SubsystemCooling System BackplaneChipset Mainboard FeaturesProcessors Memory ATI Graphics Controller Other FeaturesOnboard Scsi PCI Expansion SlotsAsia-Pacific Contacting SupermicroHeadquarters European OfficePreparing for Setup Chapter Server InstallationUnpacking the SuperServer 6012L-6 Rack Precautions Choosing a Setup LocationServer Precautions Identifying the Sections of the Rack Rails Installing the SuperServer 6012L-6 into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Unpacking Chapter Advanced Motherboard SetupPrecautions Handling the P4DLR+ MotherboardPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Data Cables Connecting CablesConnecting Power Cables P4DLR+ Front Control Panel Header Pins Connecting the Control PanelDimm Installation See Figure Installing MemoryI/O Ports Memory Support Side View of Dimm Installation into SlotAdding PCI Cards PCI card installationPCI slots Super P4DLR+ Layout Motherboard LayoutConnector Description Jumper Description Default SettingP4DLR+ Quick Reference Pwrsec Connection Connector DefinitionsATX Power Connection Power LEDReset Power Fail LEDOverheat LED OH Extra Universal Serial Bus Connection USB2/3 Universal Serial Bus USB0/1LAN1/LAN2 Ethernet Ports Serial PortsPS/2 Keyboard and Mouse Ports Fan HeadersWake-On-LAN Third Power Supply Fail HeaderSleep Button Chassis Intrusion Ipmb OptionalLAN1/LAN2 LEDs Onboard IndicatorsLED1/LED2 Debug LEDs Explanation Jumpers DIP Switch SettingsJumper Settings DIP Switch Processor SpeedFan Detection Select SpeakerEnable/DisableVGA Enable/Disable Cmos ClearChassis/Overheat Fan Select Watch Dog EnableLAN1 Enable/Disable LAN2 Enable/DisableMHz PCI Enable/Disable Scsi Enable/DisableScsi Termination Enable/ Disable PCI-X Bus Speed SettingIDE Connectors Floppy ConnectorFloppy/Hard Disk Drive and Scsi Connections U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J a Ultra160 Scsi ConnectorDriver/Tool Installation Display Screen Installing Software DriversSuperserver 6012L-6 User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Chassis Front and Rear Views Control PanelReplacing System Cooling Fans Installing a new fanSystem Fans System Fan FailureAccessing the Drive Bays Drive Bay Installation/RemovalSuperServer 6012L-6 Mounting a Scsi drive in a drive carrier Scsi Drive InstallationInstalling/removing hot-swap Scsi drives SCA Backplane CD-ROM and Floppy Drive InstallationRemoving the power supply Power SupplyPower Supply Failure Removing/Replacing the Power SupplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual Chapter System BiosHow To Change the Configuration Data Starting the Setup UtilityRunning Setup Bios FeaturesBios Setup Utility Main Bios Setup MenuMain Advanced Bios SetupSerial Port 2 Address Super IO ConfigurationSerial Port 1 Address Serial Port 1 IRQIDE Configuration Type LBA/Large ModeBlock Multi-Sector Transfer Mode Primary IDE Master32Bit Data Transfer PIO ModeDMA Mode A.R.TSecondary IDE Slave Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE MasterBoot Settings Configuration Floppy ConfigurationPS/2 Mouse Support BootUp Num LockBootUp CPU Speed Boot to OS/2Cache Wait for F1 if ErrorSystem Bios Cacheable Hit Delete Message DisplayEvent Log Configuration System Health Monitor Peripheral Device ConfigurationChipset Setup Memory Writing Posting Scrubbing EnableMemory Auto Precharge Write CombiningHide Xioapic PCI Functions PCI PnP SetupWatchdog Timer Hot Spare RowAllocate IRQ to PCI VGA Reset Configuration DataPCI Latency Timer Plug & Play OSLegacy USB Support Power SetupAcpi Aware O/S Power Management2nd Boot Device Boot SetupBoot Device Priority 1st Boot DeviceHard Disk Drives 3rd Boot Device4th Boot Device 5th Boot DeviceSupervisor Password User Password Security SetupBoot Sector Virus Protection Change Supervisor PasswordChange User Password Clear User PasswordExit Saving Changes Exit SetupExit Discarding Changes Load Failsafe Defaults Load Optimal DefaultsDiscard Changes Amibios Error Beep Codes Appendix a Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Uncompressed Initialization Codes Appendix B Amibios Post CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Expansion Slots Power SupplyDimensions Weight