SUPER MICRO Computer 6012L-6 user manual PGA Processor and Heatsink Installation

Page 36

SUPERSERVER 6012L-6 User’s Manual

5-2 PGA Processor and Heatsink Installation

When handling the processor package, avoid placing direct pressure on the label area of the fan. Also, do not place the

! motherboard on a conductive surface, which can damage the

BIOS battery and prevent the system from booting up.

IMPORTANT: Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Make sure that you install the processor into the CPU socket before you install the heatsink. The P4DLR+ can support either one or two Intel Xeon 512K L2 cache processors of 2.4+ GHz. If installing one processor only, install it into CPU socket #1.

1. Lift the lever on the CPU socket.

 

Lift the lever completely or you will

 

damage the CPU socket when

Socket lever

power is applied. (Install a

 

processor into CPU #1 socket

 

first.)

 

2. Install the CPU in the socket.

 

Make sure that pin 1 of the CPU is

 

seated on pin 1 of the socket (both

Pin 1

 

corners are marked with a

 

triangle). When using only one

 

CPU, install it into CPU socket #1

 

(CPU socket #2 is automatically

 

disabled if only one CPU is used).

 

3.Press the lever down until you hear it *click* into the locked position. See Figure 5-1 for pictures of the 603-pin CPU socket before and after the processor is

installed.

Socket lever in locked position

5-2

Image 36
Contents Super Page Preface About This ManualManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup CR5 LEDAmibios AppendicesPage Chapter Introduction to the SuperServer 6012L-6 OverviewServer Chassis Features System PowerScsi Subsystem Control PanelBackplane Cooling SystemMainboard Features ChipsetProcessors Memory Other Features Onboard ScsiPCI Expansion Slots ATI Graphics ControllerContacting Supermicro HeadquartersEuropean Office Asia-PacificChapter Server Installation Preparing for SetupUnpacking the SuperServer 6012L-6 Choosing a Setup Location Rack PrecautionsServer Precautions Installing the SuperServer 6012L-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DLR+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel P4DLR+ Front Control Panel Header PinsInstalling Memory Dimm Installation See FigureI/O Ports Side View of Dimm Installation into Slot Memory SupportPCI card installation Adding PCI CardsPCI slots Motherboard Layout Super P4DLR+ LayoutJumper Description Default Setting Connector DescriptionP4DLR+ Quick Reference Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionPower Fail LED ResetOverheat LED OH Universal Serial Bus USB0/1 Extra Universal Serial Bus Connection USB2/3Serial Ports PS/2 Keyboard and Mouse PortsFan Headers LAN1/LAN2 Ethernet PortsThird Power Supply Fail Header Wake-On-LANSleep Button Ipmb Optional Chassis IntrusionOnboard Indicators LAN1/LAN2 LEDsLED1/LED2 Debug LEDs DIP Switch Settings Jumper SettingsDIP Switch Processor Speed Explanation JumpersSpeakerEnable/Disable VGA Enable/DisableCmos Clear Fan Detection SelectWatch Dog Enable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisablePCI-X Bus Speed Setting MHz PCI Enable/DisableFloppy Connector IDE ConnectorsFloppy/Hard Disk Drive and Scsi Connections Ultra160 Scsi Connector U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J aInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012L-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysSuperServer 6012L-6 Scsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup MainSuper IO Configuration Serial Port 1 AddressSerial Port 1 IRQ Serial Port 2 AddressIDE Configuration LBA/Large Mode Block Multi-Sector Transfer ModePrimary IDE Master TypePIO Mode DMA ModeA.R.T 32Bit Data TransferAtapi Detect Timeout Seconds Primary IDE SlaveSecondary IDE Master Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBootUp Num Lock BootUp CPU SpeedBoot to OS/2 PS/2 Mouse SupportWait for F1 if Error System Bios CacheableHit Delete Message Display CacheEvent Log Configuration Peripheral Device Configuration System Health MonitorChipset Setup Scrubbing Enable Memory Auto PrechargeWrite Combining Memory Writing PostingPCI PnP Setup Watchdog TimerHot Spare Row Hide Xioapic PCI FunctionsReset Configuration Data PCI Latency TimerPlug & Play OS Allocate IRQ to PCI VGAPower Setup Legacy USB SupportPower Management Acpi Aware O/SBoot Setup Boot Device Priority1st Boot Device 2nd Boot Device3rd Boot Device 4th Boot Device5th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordChange Supervisor Password Change User PasswordClear User Password Boot Sector Virus ProtectionExit Setup Exit Saving ChangesExit Discarding Changes Load Optimal Defaults Load Failsafe DefaultsDiscard Changes Appendix a Amibios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Appendix B Amibios Post Codes Uncompressed Initialization CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Power Supply DimensionsWeight Expansion Slots