SUPER MICRO Computer 6012L-6 user manual Motherboard LEDs

Page 30

SUPERSERVER 6012L-6 User's Manual

3-5 Motherboard LEDs

The three - status CR5 LED indicates the operational state of the motherboard. When red, it indicates that an incorrect CPU has been in- stalled. Yellow indicates standby power is present and green indicates a full power on state.

There are also two surface-mounted debug LEDs designated LED1 and LED2. Each is composed of four individual LEDs, which are used to provide POST code information.

See the Onboard Indicators section in Chapter 5 for details on the motherboard LEDs.

3-4

Image 30

Contents Super Page Preface About This ManualManual Organization Advanced Chassis Setup System SafetyAdvanced Motherboard Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup CR5 LEDAmibios AppendicesPage Chapter Introduction to the SuperServer 6012L-6 OverviewScsi Subsystem Server Chassis FeaturesSystem Power Control PanelBackplane Cooling SystemMainboard Features ChipsetProcessors Memory PCI Expansion Slots Other FeaturesOnboard Scsi ATI Graphics ControllerEuropean Office Contacting SupermicroHeadquarters Asia-PacificChapter Server Installation Preparing for SetupUnpacking the SuperServer 6012L-6 Choosing a Setup Location Rack PrecautionsServer Precautions Installing the SuperServer 6012L-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Handling the P4DLR+ Motherboard Chapter Advanced Motherboard SetupPrecautions UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel P4DLR+ Front Control Panel Header PinsInstalling Memory Dimm Installation See FigureI/O Ports Side View of Dimm Installation into Slot Memory SupportPCI card installation Adding PCI CardsPCI slots Motherboard Layout Super P4DLR+ LayoutJumper Description Default Setting Connector DescriptionP4DLR+ Quick Reference Power LED Connector DefinitionsATX Power Connection Pwrsec ConnectionPower Fail LED ResetOverheat LED OH Universal Serial Bus USB0/1 Extra Universal Serial Bus Connection USB2/3Fan Headers Serial PortsPS/2 Keyboard and Mouse Ports LAN1/LAN2 Ethernet PortsThird Power Supply Fail Header Wake-On-LANSleep Button Ipmb Optional Chassis IntrusionOnboard Indicators LAN1/LAN2 LEDsLED1/LED2 Debug LEDs DIP Switch Processor Speed DIP Switch SettingsJumper Settings Explanation JumpersCmos Clear SpeakerEnable/DisableVGA Enable/Disable Fan Detection SelectLAN2 Enable/Disable Watch Dog EnableLAN1 Enable/Disable Chassis/Overheat Fan SelectPCI-X Bus Speed Setting Scsi Enable/DisableScsi Termination Enable/ Disable MHz PCI Enable/DisableFloppy Connector IDE ConnectorsFloppy/Hard Disk Drive and Scsi Connections Ultra160 Scsi Connector U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J aInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012L-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel Chassis Front and Rear ViewsSystem Fan Failure Installing a new fanSystem Fans Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysSuperServer 6012L-6 Scsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplaneRemoving/Replacing the Power Supply Power SupplyPower Supply Failure Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual Starting the Setup Utility System BiosHow To Change the Configuration Data ChapterBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup MainSerial Port 1 IRQ Super IO ConfigurationSerial Port 1 Address Serial Port 2 AddressIDE Configuration Primary IDE Master LBA/Large ModeBlock Multi-Sector Transfer Mode TypeA.R.T PIO ModeDMA Mode 32Bit Data TransferSecondary IDE Master Atapi Detect Timeout SecondsPrimary IDE Slave Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBoot to OS/2 BootUp Num LockBootUp CPU Speed PS/2 Mouse SupportHit Delete Message Display Wait for F1 if ErrorSystem Bios Cacheable CacheEvent Log Configuration Peripheral Device Configuration System Health MonitorChipset Setup Write Combining Scrubbing EnableMemory Auto Precharge Memory Writing PostingHot Spare Row PCI PnP SetupWatchdog Timer Hide Xioapic PCI FunctionsPlug & Play OS Reset Configuration DataPCI Latency Timer Allocate IRQ to PCI VGAPower Setup Legacy USB SupportPower Management Acpi Aware O/S1st Boot Device Boot SetupBoot Device Priority 2nd Boot Device5th Boot Device 3rd Boot Device4th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordClear User Password Change Supervisor PasswordChange User Password Boot Sector Virus ProtectionExit Setup Exit Saving ChangesExit Discarding Changes Load Optimal Defaults Load Failsafe DefaultsDiscard Changes Appendix a Amibios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Appendix B Amibios Post Codes Uncompressed Initialization CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Weight Power SupplyDimensions Expansion Slots