SUPER MICRO Computer 6012L-6 user manual IDE Configuration

Page 76

SUPERSERVER 6012L-6 Manual

Serial Port 2 Mode

Use this option to choose the Serial Port 2 Mode. The settings are Normal, Sharp-IR, SIR and consumer.

Parallel Port Address

This option specifies the I/O address used by the parallel port. The settings for this item include Disabled, 378, 278 and 3BC. Select your setting and then press "Enter".

Parallel Port IRQ

This option allows the user to set the Parallel Port IRQ. The settings for this item include 5 and 7.

Parallel Port Mode

This option specifies the parallel port mode. The settings for this item include Normal, Bi-directional, EPP and ECP.

ECP Mode DMA Channel

This option allows the user to set the setting for the ECP Mode of the DMA Channel. The settings for this item include 0, 1 and 3.

IDE Configuration

Onboard PCI IDE Controller

This option allows the user to enable or disable the integrated IDE Control- ler. The settings include Disabled, Primary, Second and Both. Select "Dis- abled" to disable the Integrated IDE Controller. Select "Primary" to enable the Primary IDE ontroller only. Select "Secondary" to enable the Secondary IDE Controller only. Select "Both" to enable both Primary and Secondary IDE Controllers.

7-6

Image 76

Contents Super Page About This Manual PrefaceManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup CR5 LEDAmibios AppendicesPage Chapter Introduction to the SuperServer 6012L-6 OverviewServer Chassis Features System PowerScsi Subsystem Control PanelBackplane Cooling SystemChipset Mainboard FeaturesProcessors Memory Other Features Onboard ScsiPCI Expansion Slots ATI Graphics ControllerContacting Supermicro HeadquartersEuropean Office Asia-PacificPreparing for Setup Chapter Server InstallationUnpacking the SuperServer 6012L-6 Rack Precautions Choosing a Setup LocationServer Precautions Installing the SuperServer 6012L-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DLR+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel P4DLR+ Front Control Panel Header PinsDimm Installation See Figure Installing MemoryI/O Ports Side View of Dimm Installation into Slot Memory SupportAdding PCI Cards PCI card installationPCI slots Motherboard Layout Super P4DLR+ LayoutConnector Description Jumper Description Default SettingP4DLR+ Quick Reference Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionReset Power Fail LEDOverheat LED OH Universal Serial Bus USB0/1 Extra Universal Serial Bus Connection USB2/3Serial Ports PS/2 Keyboard and Mouse PortsFan Headers LAN1/LAN2 Ethernet PortsWake-On-LAN Third Power Supply Fail HeaderSleep Button Ipmb Optional Chassis IntrusionLAN1/LAN2 LEDs Onboard IndicatorsLED1/LED2 Debug LEDs DIP Switch Settings Jumper SettingsDIP Switch Processor Speed Explanation JumpersSpeakerEnable/Disable VGA Enable/DisableCmos Clear Fan Detection SelectWatch Dog Enable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisablePCI-X Bus Speed Setting MHz PCI Enable/DisableIDE Connectors Floppy ConnectorFloppy/Hard Disk Drive and Scsi Connections Ultra160 Scsi Connector U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J aInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012L-6 User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansAccessing the Drive Bays Drive Bay Installation/RemovalSuperServer 6012L-6 Scsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup MainSuper IO Configuration Serial Port 1 AddressSerial Port 1 IRQ Serial Port 2 AddressIDE Configuration LBA/Large Mode Block Multi-Sector Transfer ModePrimary IDE Master TypePIO Mode DMA ModeA.R.T 32Bit Data TransferAtapi Detect Timeout Seconds Primary IDE SlaveSecondary IDE Master Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBootUp Num Lock BootUp CPU SpeedBoot to OS/2 PS/2 Mouse SupportWait for F1 if Error System Bios CacheableHit Delete Message Display CacheEvent Log Configuration Peripheral Device Configuration System Health MonitorChipset Setup Scrubbing Enable Memory Auto PrechargeWrite Combining Memory Writing PostingPCI PnP Setup Watchdog TimerHot Spare Row Hide Xioapic PCI FunctionsReset Configuration Data PCI Latency TimerPlug & Play OS Allocate IRQ to PCI VGAPower Setup Legacy USB SupportPower Management Acpi Aware O/SBoot Setup Boot Device Priority1st Boot Device 2nd Boot Device3rd Boot Device 4th Boot Device5th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordChange Supervisor Password Change User PasswordClear User Password Boot Sector Virus ProtectionExit Saving Changes Exit SetupExit Discarding Changes Load Failsafe Defaults Load Optimal DefaultsDiscard Changes Amibios Error Beep Codes Appendix a Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Uncompressed Initialization Codes Appendix B Amibios Post CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Power Supply DimensionsWeight Expansion Slots