SUPER MICRO Computer 6012L-6 user manual Control Panel LEDs

Page 28

SUPERSERVER 6012L-6 User's Manual

lPOWER: This is the main power button, which is used to apply or turn off the main system power. Turning off system power with this button removes the main power but keeps standby power supplied to the system.

3-3 Control Panel LEDs

The control panel located on the front of the SC812-EO chassis has five LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take.

lOverheat: Indicates an overheat condition in the chassis. This may be caused by cables obstructing the airflow in the system or the ambient room temperature being too warm. You should also check to make sure that the chassis cover is installed and that all fans are present and operat- ing normally. Verify that the heatsinks are installed properly (see Chapter 5). Finally, check the air seals for damage. The air seals are vertical pieces located to the left and right of the fans and against the front side of the chassis frame cross section that separates the drive bay area from the motherboard area of the chassis. There is also a small air seal positioned between the two fans.

NIC2

l NIC2: Indicates network activity on LAN2 when flashing.

3-2

Image 28
Contents Super Page About This Manual PrefaceManual Organization System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup CR5 LEDAmibios AppendicesPage Chapter Introduction to the SuperServer 6012L-6 OverviewServer Chassis Features System PowerScsi Subsystem Control PanelBackplane Cooling SystemChipset Mainboard FeaturesProcessors Memory Other Features Onboard ScsiPCI Expansion Slots ATI Graphics ControllerContacting Supermicro HeadquartersEuropean Office Asia-PacificPreparing for Setup Chapter Server InstallationUnpacking the SuperServer 6012L-6 Rack Precautions Choosing a Setup LocationServer Precautions Installing the SuperServer 6012L-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DLR+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control Panel P4DLR+ Front Control Panel Header PinsDimm Installation See Figure Installing MemoryI/O Ports Side View of Dimm Installation into Slot Memory SupportAdding PCI Cards PCI card installationPCI slots Motherboard Layout Super P4DLR+ LayoutConnector Description Jumper Description Default SettingP4DLR+ Quick Reference Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionReset Power Fail LEDOverheat LED OH Universal Serial Bus USB0/1 Extra Universal Serial Bus Connection USB2/3Serial Ports PS/2 Keyboard and Mouse PortsFan Headers LAN1/LAN2 Ethernet PortsWake-On-LAN Third Power Supply Fail HeaderSleep Button Ipmb Optional Chassis IntrusionLAN1/LAN2 LEDs Onboard IndicatorsLED1/LED2 Debug LEDs DIP Switch Settings Jumper SettingsDIP Switch Processor Speed Explanation JumpersSpeakerEnable/Disable VGA Enable/DisableCmos Clear Fan Detection SelectWatch Dog Enable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisablePCI-X Bus Speed Setting MHz PCI Enable/DisableIDE Connectors Floppy ConnectorFloppy/Hard Disk Drive and Scsi Connections Ultra160 Scsi Connector U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J aInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012L-6 User’s Manual Static-Sensitive Devices Chapter Advanced Chassis SetupTools Required Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansAccessing the Drive Bays Drive Bay Installation/RemovalSuperServer 6012L-6 Scsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup MainSuper IO Configuration Serial Port 1 AddressSerial Port 1 IRQ Serial Port 2 AddressIDE Configuration LBA/Large Mode Block Multi-Sector Transfer ModePrimary IDE Master TypePIO Mode DMA ModeA.R.T 32Bit Data TransferAtapi Detect Timeout Seconds Primary IDE SlaveSecondary IDE Master Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBootUp Num Lock BootUp CPU SpeedBoot to OS/2 PS/2 Mouse SupportWait for F1 if Error System Bios CacheableHit Delete Message Display CacheEvent Log Configuration Peripheral Device Configuration System Health MonitorChipset Setup Scrubbing Enable Memory Auto PrechargeWrite Combining Memory Writing PostingPCI PnP Setup Watchdog TimerHot Spare Row Hide Xioapic PCI FunctionsReset Configuration Data PCI Latency TimerPlug & Play OS Allocate IRQ to PCI VGAPower Setup Legacy USB SupportPower Management Acpi Aware O/SBoot Setup Boot Device Priority1st Boot Device 2nd Boot Device3rd Boot Device 4th Boot Device5th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordChange Supervisor Password Change User PasswordClear User Password Boot Sector Virus ProtectionExit Saving Changes Exit SetupExit Discarding Changes Load Failsafe Defaults Load Optimal DefaultsDiscard Changes Amibios Error Beep Codes Appendix a Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Uncompressed Initialization Codes Appendix B Amibios Post CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Power Supply DimensionsWeight Expansion Slots