SUPER MICRO Computer 6012L-6 user manual Amibios, Appendices

Page 9

 

 

Table of Contents

 

 

 

 

CD-ROM and Floppy Drive Installation

6-7

6-5

Power Supply

6-8

 

Power Supply Failure

6-8

 

Removing/Replacing the Power Supply

6-8

Chapter 7: AMIBIOS

 

7-1

Introduction

7-1

7-2

BIOS Features

7-2

7-3

Running Setup

7-2

7-4

Advanced BIOS Setup

7-4

7-5

Chipset Setup

7-15

7-6

PCI PnP Setup

7-17

7-7

Power Setup

7-19

7-8

Boot Setup

7-21

7-9

Security Setup

7-23

7-10

Exit Setup

7-25

Appendices:

 

Appendix A: AMIBIOS Error Beep Codes

A - 1

Appendix B: AMIBIOS Post Codes

B-1

Appendix C: System Specifications

C-1

ix

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Super Page Preface About This ManualManual Organization Advanced Motherboard Setup System SafetyAdvanced Chassis Setup BiosPreface Table of Contents Advanced Motherboard Setup System SafetyCR5 LED Advanced Chassis SetupAppendices AmibiosPage Overview Chapter Introduction to the SuperServer 6012L-6System Power Server Chassis FeaturesScsi Subsystem Control PanelCooling System BackplaneMainboard Features ChipsetProcessors Memory Onboard Scsi Other FeaturesPCI Expansion Slots ATI Graphics ControllerHeadquarters Contacting SupermicroEuropean Office Asia-PacificChapter Server Installation Preparing for SetupUnpacking the SuperServer 6012L-6 Choosing a Setup Location Rack PrecautionsServer Precautions Identifying the Sections of the Rack Rails Installing the SuperServer 6012L-6 into a RackInstalling the Rack Rails Installing the Chassis RailsInstalling the Server into a Rack Installing the Server into the RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Control Panel Buttons Chapter System InterfaceControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Operating Precautions Precautions Chapter Advanced Motherboard SetupHandling the P4DLR+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Cables Connecting Data CablesConnecting Power Cables P4DLR+ Front Control Panel Header Pins Connecting the Control PanelInstalling Memory Dimm Installation See FigureI/O Ports Memory Support Side View of Dimm Installation into SlotPCI card installation Adding PCI CardsPCI slots Super P4DLR+ Layout Motherboard LayoutJumper Description Default Setting Connector DescriptionP4DLR+ Quick Reference ATX Power Connection Connector DefinitionsPower LED Pwrsec ConnectionPower Fail LED ResetOverheat LED OH Extra Universal Serial Bus Connection USB2/3 Universal Serial Bus USB0/1PS/2 Keyboard and Mouse Ports Serial PortsFan Headers LAN1/LAN2 Ethernet PortsThird Power Supply Fail Header Wake-On-LANSleep Button Chassis Intrusion Ipmb OptionalOnboard Indicators LAN1/LAN2 LEDsLED1/LED2 Debug LEDs Jumper Settings DIP Switch SettingsDIP Switch Processor Speed Explanation JumpersVGA Enable/Disable SpeakerEnable/DisableCmos Clear Fan Detection SelectLAN1 Enable/Disable Watch Dog EnableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Termination Enable/ Disable Scsi Enable/DisablePCI-X Bus Speed Setting MHz PCI Enable/DisableFloppy Connector IDE ConnectorsFloppy/Hard Disk Drive and Scsi Connections U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J a Ultra160 Scsi ConnectorDriver/Tool Installation Display Screen Installing Software DriversSuperserver 6012L-6 User’s Manual Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Chassis Front and Rear Views Control PanelSystem Fans Installing a new fanSystem Fan Failure Replacing System Cooling FansDrive Bay Installation/Removal Accessing the Drive BaysSuperServer 6012L-6 Mounting a Scsi drive in a drive carrier Scsi Drive InstallationInstalling/removing hot-swap Scsi drives SCA Backplane CD-ROM and Floppy Drive InstallationPower Supply Failure Power SupplyRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual How To Change the Configuration Data System BiosStarting the Setup Utility ChapterRunning Setup Bios FeaturesBios Setup Utility Main Bios Setup MenuMain Advanced Bios SetupSerial Port 1 Address Super IO ConfigurationSerial Port 1 IRQ Serial Port 2 AddressIDE Configuration Block Multi-Sector Transfer Mode LBA/Large ModePrimary IDE Master TypeDMA Mode PIO ModeA.R.T 32Bit Data TransferPrimary IDE Slave Atapi Detect Timeout SecondsSecondary IDE Master Secondary IDE SlaveBoot Settings Configuration Floppy ConfigurationBootUp CPU Speed BootUp Num LockBoot to OS/2 PS/2 Mouse SupportSystem Bios Cacheable Wait for F1 if ErrorHit Delete Message Display CacheEvent Log Configuration System Health Monitor Peripheral Device ConfigurationChipset Setup Memory Auto Precharge Scrubbing EnableWrite Combining Memory Writing PostingWatchdog Timer PCI PnP SetupHot Spare Row Hide Xioapic PCI FunctionsPCI Latency Timer Reset Configuration DataPlug & Play OS Allocate IRQ to PCI VGALegacy USB Support Power SetupAcpi Aware O/S Power ManagementBoot Device Priority Boot Setup1st Boot Device 2nd Boot Device4th Boot Device 3rd Boot Device5th Boot Device Hard Disk DrivesSupervisor Password User Password Security SetupChange User Password Change Supervisor PasswordClear User Password Boot Sector Virus ProtectionExit Setup Exit Saving ChangesExit Discarding Changes Load Optimal Defaults Load Failsafe DefaultsDiscard Changes Appendix a Amibios Error Beep Codes Amibios Error Beep CodesBeep Code Error Message Description Superserver 6012L-6 Manual Appendix B Amibios Post Codes Uncompressed Initialization CodesCheckpoint Code Description Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Dimensions Power SupplyWeight Expansion Slots
Top Page Image Contents