SUPER MICRO Computer 6012L-6 user manual Installing the Chassis Rails, Installing the Rack Rails

Page 20

SUPERSERVER 6012L-6 Manual

Installing the Chassis Rails:

Position the fixed chassis rail sections you just removed along the side of the 6012L-6 making sure the screw holes line up. Note that these two rails are left/right specific. Screw the rail securely to the side of the chassis (see Figure 2-2). Repeat this procedure for the other rail on the other side of the chassis. You will also need to attach the rail brackets when installng into a telco rack.

Locking Tabs: As you have seen, both chassis rails have a locking tab, which serves two functions. The first is to lock the server into place when installed and pushed fully into the rack, which is its normal position. Secondly, these tabs also lock the server in place when fully extended from the rack. This prevents the server from coming completely out of the rack when you pull it out for servicing.

Figure 2-2. Installing Chassis Rails

Installing the Rack Rails:

Determine where you want to place the SuperServer 6012L-6 in the rack. (See Rack and Server Precautions in Section 2-3.) Position the fixed rack rail/sliding rail guide assemblies at the desired location in the rack, keeping the sliding rail guide facing the inside of the rack. Screw the assembly securely to the rack using the brackets provided. Attach the other assem-

2-4

Image 20
Contents Super Page Manual Organization PrefaceAbout This Manual System Safety Advanced Motherboard SetupAdvanced Chassis Setup BiosPreface Table of Contents System Safety Advanced Motherboard SetupAdvanced Chassis Setup CR5 LEDAmibios AppendicesPage Chapter Introduction to the SuperServer 6012L-6 OverviewServer Chassis Features System PowerScsi Subsystem Control PanelBackplane Cooling SystemProcessors Memory Mainboard FeaturesChipset Other Features Onboard ScsiPCI Expansion Slots ATI Graphics ControllerContacting Supermicro HeadquartersEuropean Office Asia-PacificUnpacking the SuperServer 6012L-6 Chapter Server InstallationPreparing for Setup Server Precautions Choosing a Setup LocationRack Precautions Installing the SuperServer 6012L-6 into a Rack Identifying the Sections of the Rack RailsInstalling the Chassis Rails Installing the Rack RailsInstalling the Server into the Rack Installing the Server into a RackInstalling the Server into a Telco Rack Installing the Server into a Telco RackChecking the Motherboard Setup Superserver 6012L-6 Manual Checking the Drive Bay Setup Superserver 6012L-6 Manual Chapter System Interface Control Panel ButtonsControl Panel LEDs Scsi Drive Carrier LEDs Motherboard LEDs Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Chapter Advanced Motherboard Setup PrecautionsHandling the P4DLR+ Motherboard UnpackingPGA Processor and Heatsink Installation PGA Socket Empty and with Processor Installed Heatsink Installation Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control Panel P4DLR+ Front Control Panel Header PinsI/O Ports Installing MemoryDimm Installation See Figure Side View of Dimm Installation into Slot Memory SupportPCI slots PCI card installationAdding PCI Cards Motherboard Layout Super P4DLR+ LayoutP4DLR+ Quick Reference Jumper Description Default SettingConnector Description Connector Definitions ATX Power ConnectionPower LED Pwrsec ConnectionOverheat LED OH Power Fail LEDReset Universal Serial Bus USB0/1 Extra Universal Serial Bus Connection USB2/3Serial Ports PS/2 Keyboard and Mouse PortsFan Headers LAN1/LAN2 Ethernet PortsSleep Button Third Power Supply Fail HeaderWake-On-LAN Ipmb Optional Chassis IntrusionLED1/LED2 Debug LEDs Onboard IndicatorsLAN1/LAN2 LEDs DIP Switch Settings Jumper SettingsDIP Switch Processor Speed Explanation JumpersSpeakerEnable/Disable VGA Enable/DisableCmos Clear Fan Detection SelectWatch Dog Enable LAN1 Enable/DisableLAN2 Enable/Disable Chassis/Overheat Fan SelectScsi Enable/Disable Scsi Termination Enable/ DisablePCI-X Bus Speed Setting MHz PCI Enable/DisableFloppy/Hard Disk Drive and Scsi Connections Floppy ConnectorIDE Connectors Ultra160 Scsi Connector U ltra 1 6 0 S C S I C o nn e c to rs J a 1 , J a 2 , J aInstalling Software Drivers Driver/Tool Installation Display ScreenSuperserver 6012L-6 User’s Manual Tools Required Chapter Advanced Chassis SetupStatic-Sensitive Devices Control Panel Chassis Front and Rear ViewsInstalling a new fan System FansSystem Fan Failure Replacing System Cooling FansSuperServer 6012L-6 Drive Bay Installation/RemovalAccessing the Drive Bays Scsi Drive Installation Mounting a Scsi drive in a drive carrierInstalling/removing hot-swap Scsi drives CD-ROM and Floppy Drive Installation SCA BackplanePower Supply Power Supply FailureRemoving/Replacing the Power Supply Removing the power supplyRemoving/Replacing the Power Supply Superserver 6012L-6 Manual System Bios How To Change the Configuration DataStarting the Setup Utility ChapterBios Features Running SetupMain Bios Setup Menu Bios Setup UtilityAdvanced Bios Setup MainSuper IO Configuration Serial Port 1 AddressSerial Port 1 IRQ Serial Port 2 AddressIDE Configuration LBA/Large Mode Block Multi-Sector Transfer ModePrimary IDE Master TypePIO Mode DMA ModeA.R.T 32Bit Data TransferAtapi Detect Timeout Seconds Primary IDE SlaveSecondary IDE Master Secondary IDE SlaveFloppy Configuration Boot Settings ConfigurationBootUp Num Lock BootUp CPU SpeedBoot to OS/2 PS/2 Mouse SupportWait for F1 if Error System Bios CacheableHit Delete Message Display CacheEvent Log Configuration Peripheral Device Configuration System Health MonitorChipset Setup Scrubbing Enable Memory Auto PrechargeWrite Combining Memory Writing PostingPCI PnP Setup Watchdog TimerHot Spare Row Hide Xioapic PCI FunctionsReset Configuration Data PCI Latency TimerPlug & Play OS Allocate IRQ to PCI VGAPower Setup Legacy USB SupportPower Management Acpi Aware O/SBoot Setup Boot Device Priority1st Boot Device 2nd Boot Device3rd Boot Device 4th Boot Device5th Boot Device Hard Disk DrivesSecurity Setup Supervisor Password User PasswordChange Supervisor Password Change User PasswordClear User Password Boot Sector Virus ProtectionExit Discarding Changes Exit SetupExit Saving Changes Discard Changes Load Optimal DefaultsLoad Failsafe Defaults Beep Code Error Message Description Appendix a Amibios Error Beep CodesAmibios Error Beep Codes Superserver 6012L-6 Manual Checkpoint Code Description Appendix B Amibios Post CodesUncompressed Initialization Codes Bootblock Recovery Codes Initialization before the keyboard BAT command is issued Monochrome mode and color mode settings next 48h 60h 95h Superserver 6012L-6 Manual Appendix C System Specifications Power Supply DimensionsWeight Expansion Slots