Infinite Peripherals manual 0630,1,Door is opened 0630,2,Door is closed, My SCOM-100

Page 24

SCOM-100, User guide

24

Let us specify alarm text messages for the previous example. The message for the positive (0 to 1) transition should be ‘Door is opened’. The respective message for the negative transition should be ‘Door is closed’.

The commands to configure these text messages are:

0630,1,Door is opened; 0630,2,Door is closed

Now we have to associate the text messages to the signal transitions of the example.

The respective command for our example is: 1101,0,1,2,1

We can pack all three commands in one SMS message and send them to the SCOM-100 unit:

0630,1,Door is opened; 0630,2,Door is closed; 1101,0,1,2,1

After sending and receiving an ‘OK’ response, repeat the signal changes by closing the contact/loop for at least 30 seconds and then open it again.

Closing of the input for at least 30 seconds will issue an alarm SMS with the following contents:

My SCOM-100

Door contact

Door is opened

Opening the contact/loop for at least 30 seconds will issue the negative transition alarm message:

My SCOM-100

Image 24

Contents Page Disclaimer Contents Page Page Device overview ConnectionsLED indications Wiring Power supplyDigital inputs Digital outputs AC1Analog inputs Analog inputVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna MicrophoneInstalling the SIM card Getting startedPreparing a SIM card First power up & factory settings SMS commands Device operationNaming the unit XXXX,A..A,..,..,Z..ZConfiguring a digital input for alarming 1100,m,n,s,a,d1100,0,1,Door contact,3,30 My SCOM-100 Door contactSetting alarm message’s texts 0630,ID,s1101,m,n,ID1,ID2 0630,1,Door is opened 0630,2,Door is closed 0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1My SCOM-100 Door contact Door is opened My SCOM-100Clearing the digital input configuration Door contact Door is closed1110,m,n Setting a digital output Controlling the digital outputs1000,m,n 1000,0,2Configuring an output as a closed contact 1001,0,21071,m,n 1071,0,21070,m,n Pulse digital outputSetting a digital output after a delay 1010,m,n,s1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moffTime schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D1700,1,0,800-120,1130-1001645-180 1030,m,n,ID1701,ID,P Clearing the digital output configuration 1701,3,501090,m,n,ID Analog signal alarming Analog input configuration1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide Setting alarm message’s texts for analog inputs 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,151201,m,n,ID1,ID2 Clearing the analog input configuration Setting the analog inputs alarm deadband1210,m,n 1800,dSpecial I/O Functions 1 ON/OFF and PID control1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s1252,id,m,n 1253,id1260,id User administration Create a new user0500,id,n,p,c1,c2,c3 Change user configuration Defining specific alarm recipientsSet a DI alarm recipient Delete a userSet an AI alarm recipient Clear DI alarm recipientsClear AI alarm recipients Device status & mode controls Setting the device statusRUN Control command Monitor commandControlling the device status Controlling the device response1105,m,n,v Send acknowledgement SMSSetting up an SMS counter Merge concurrent alarmsResponse format Setting date and time Setting a GSM PINMonitoring commands Monitoring capabilities5100 UNITMy SCOM-100Connecting a PC Using the Hyperterminal for configurationSCOM-100, User guide SCOM-100, User guide Using the Scom Configurator for configuration Ate1Atsms=1100,0,1,Door contact,3,30 Using the microphone input Command reference General parameter settingsAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unitGE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LEDDefault parameter values Factory settings GE-DIO-42 Digital I/O expansionSetting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN