Infinite Peripherals SCOM-100 manual RTC & Time scheduling

Page 63

	SCOM-100, User guide			63

	Cmd	Description		Syntax	Comments
	1255	Set PID		cmd,id,sp	id:1-4, sp:-100000-
		Control Set			100000
		Point
	1260	Clear PID		cmd,id	id:1-4
		Control
		Configuration
	1105	Set DI for		cmd,m,n,v	m:0-8, n:1-4, v:0-1
		device
		Status
		control

9.1.6 RTC & Time scheduling

Cmd	Description	Syntax	Comments
1600	Set RTC Time	cmd,d,m,y,h,m,	d: Day of month (1-
		s	31), m: Month of
			year (1-12), y:Year,
			h:Hour, m:Minutes,
			s:Seconds
1700	Set Time	cmd,id,d,	id:1-10,
	Schedule Day	p1b-p1d,	d:1-7
		p2b-p2d,…,	(1:Sun, 2:Mon, etc)
		p8b-p8d
1701	Set Time	cmd,id,p	id:1-10, p:0-100
	Schedule
	Duration Percent
1710	Clear Time	cmd,id	id:1-10
	Schedule

Image 63

Contents Page Disclaimer Contents Page Page Connections Device overviewLED indications Power supply WiringDigital inputs AC1 Digital outputsAnalog input Analog inputsVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antennaInstalling the SIM card Getting startedPreparing a SIM card First power up & factory settings XXXX,A..A,..,..,Z..Z SMS commandsDevice operation Naming the unit1100,m,n,s,a,d Configuring a digital input for alarmingMy SCOM-100 Door contact 1100,0,1,Door contact,3,30Setting alarm message’s texts 0630,ID,s1101,m,n,ID1,ID2 My SCOM-100 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is openedClearing the digital input configuration Door contact Door is closed1110,m,n 1000,0,2 Setting a digital outputControlling the digital outputs 1000,m,n1071,0,2 Configuring an output as a closed contact1001,0,2 1071,m,nPulse digital output 1070,m,nSetting a digital output after a delay 1010,m,n,s1010,0,2,25 1020,m,n,h,mn Resetting a digital output after a delay1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program1700,1,0,800-120,1130-1001645-180 1030,m,n,ID1701,ID,P Clearing the digital output configuration 1701,3,501090,m,n,ID Analog signal alarming Analog input configuration1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide Setting alarm message’s texts for analog inputs 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,151201,m,n,ID1,ID2 1800,d Clearing the analog input configurationSetting the analog inputs alarm deadband 1210,m,nSpecial I/O Functions 1 ON/OFF and PID control1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1251,id,s 1255,id,sp1252,id,m,n 1253,id1260,id User administration Create a new user0500,id,n,p,c1,c2,c3 Delete a user Change user configurationDefining specific alarm recipients Set a DI alarm recipientSet an AI alarm recipient Clear DI alarm recipientsClear AI alarm recipients Monitor command Device status & mode controlsSetting the device status RUN Control commandSend acknowledgement SMS Controlling the device statusControlling the device response 1105,m,n,vSetting up an SMS counter Merge concurrent alarmsResponse format Setting a GSM PIN Setting date and timeUNITMy SCOM-100 Monitoring commandsMonitoring capabilities 5100Using the Hyperterminal for configuration Connecting a PCSCOM-100, User guide SCOM-100, User guide Using the Scom Configurator for configuration Ate1Atsms=1100,0,1,Door contact,3,30 Using the microphone input Command reference General parameter settingsAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specificationsGE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indicationsGE-DIO-42 Digital I/O expansion Default parameter values Factory settingsSetting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout