Infinite Peripherals SCOM-100 manual Set an AI alarm recipient, Clear DI alarm recipients

Page 46


SCOM-100, User guide		46
n:	DI input number (1-4)
id:	User ID (1-20)

5.4.2Set an AI alarm recipient

1202,m,n,id

1202:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-4 for AI-4 expansion units)
n:	AI input number (1-2 for SCOM-100
	main unit, 1-4 for AI-4 expansion units)
id:	User ID (1-20)

5.4.3 Clear DI alarm recipients

The command removes all recipients for a specific DI alarm.

1109,m,n
1109:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-8 for DI-42 I/O expansion units)
n:	DI input number (1-4)

5.4.4 Clear AI alarm recipients

The command removes all recipients for a specific AI alarm.

1209,m,n
1209:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-4 for AI-4 expansion units)
n:	AI input number (1-2 for SCOM-100
	main unit, 1-4 for AI-4 expansion units)

Image 46

Contents Page Disclaimer Contents Page Page Device overview ConnectionsLED indications Wiring Power supplyDigital inputs Digital outputs AC1Analog inputs Analog inputVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna MicrophoneGetting started Installing the SIM cardPreparing a SIM card First power up & factory settings Naming the unit SMS commandsDevice operation XXXX,A..A,..,..,Z..ZConfiguring a digital input for alarming 1100,m,n,s,a,d1100,0,1,Door contact,3,30 My SCOM-100 Door contact0630,ID,s Setting alarm message’s texts1101,m,n,ID1,ID2 My SCOM-100 Door contact Door is opened 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100Door contact Door is closed Clearing the digital input configuration1110,m,n 1000,m,n Setting a digital outputControlling the digital outputs 1000,0,21071,m,n Configuring an output as a closed contact1001,0,2 1071,0,21070,m,n Pulse digital output1010,m,n,s Setting a digital output after a delay1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moffTime schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D1030,m,n,ID 1700,1,0,800-120,1130-1001645-1801701,ID,P 1701,3,50 Clearing the digital output configuration1090,m,n,ID Analog input configuration Analog signal alarming1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 Setting alarm message’s texts for analog inputs1201,m,n,ID1,ID2 1210,m,n Clearing the analog input configurationSetting the analog inputs alarm deadband 1800,d1 ON/OFF and PID control Special I/O Functions1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s1253,id 1252,id,m,n1260,id Create a new user User administration0500,id,n,p,c1,c2,c3 Set a DI alarm recipient Change user configurationDefining specific alarm recipients Delete a userClear DI alarm recipients Set an AI alarm recipientClear AI alarm recipients RUN Control command Device status & mode controlsSetting the device status Monitor command1105,m,n,v Controlling the device statusControlling the device response Send acknowledgement SMSMerge concurrent alarms Setting up an SMS counterResponse format Setting date and time Setting a GSM PIN5100 Monitoring commandsMonitoring capabilities UNITMy SCOM-100Connecting a PC Using the Hyperterminal for configurationSCOM-100, User guide SCOM-100, User guide Ate1 Using the Scom Configurator for configurationAtsms=1100,0,1,Door contact,3,30 Using the microphone input General parameter settings Command referenceAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unitGE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LEDDefault parameter values Factory settings GE-DIO-42 Digital I/O expansionSetting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN